Search results

  1. B

    Steering cable stuck?

    Got it out. Just used a little liquid wrench and a little more "oomph". Cable is frozen up tighter than a nun's you-know-what. Can't wait to see how she steers with a new one installed. The slider on the end of the cable is what threw me off. I wasn't sure how the whole thing was assembled.
  2. B

    Steering cable stuck?

    I'll give it a shot
  3. B

    Steering cable stuck?

    photos
  4. B

    Steering cable stuck?

    Hello, I am trying to replace my steering cable on a 1993 alpha one gen II. I've loosened the nut and unhooked the rack from under the steering wheel, I've also removed the pin from the yoke that attaches to the lower unit. I can pull the cable out about 6 inches but then it stops and won't go...
  5. B

    Quicksilver gimbal bearing dot alignment

    Thanks a bunch everyone! I really appreciate it!
  6. B

    Quicksilver gimbal bearing dot alignment

    Hello I just installed a new quicksilver sealed gimbal bearing. Unfortunately I didn’t know what I was supposed to apparently line up the dot on the outboard side of the bearing with the 10 o’clock position when I pounded it in. I didn’t think it would matter because I didn’t have a grease port...
  7. B

    Gimbal bearing install fail?

    Well I went back and bought a new link belt / sierra bearing off ebay. Seemed to be the same OD as the original bearing I pulled. When I tried to install the thing I got it started cocked and had to pull it back out with my slide hammer. Now my new bearing makes noise when I spin it. I am...
  8. B

    Gimbal bearing install fail?

    Another note - I measure the OD of the bearing compared to the original one - it was 0.015” smaller. This is quite a difference. Got this bearing in a kit from SEI marine a few years ago.
  9. B

    Gimbal bearing install fail?

    I used this to install the bearing. Bearing came out with two hits of my slide hammer. Looks like grease was getting to the hole.
  10. B

    Gimbal bearing install fail?

    That’s what I figured. I don’t think I’d trust this one after removal. Amazon gets some more money out of me. Thanks!
  11. B

    Gimbal bearing install fail?

    Adding to the above - it seems to all be coming out the back between the housing and the bearing. I checked the front behind the grease seal and none seems to be coming out of the bearing itself. I’m thinking I should have bought a sealed bearing and not let myself screw this up!
  12. B

    Gimbal bearing install fail?

    I installed my gimbal bearing last night after letting it chill in the freezer for a couple of days. I made the mistake of installing the bellows first which made it harder to see my marks for the grease hole alightnment. It went in beautifully but after getting it installed I realized that I...
  13. B

    Transom Flatness out of Tolerance

    I am disgusted with myself, once again. I clamped the heck out of my transom when installing the new wood and now the outer skin is outside the flatness tolerance. It appears to be right at 3/32" in the middle of the keyhole. See attached photo. Any tips on what I should do to fix it? Sand off...
  14. B

    Did I grind too much??

    I am afraid that I may have ground too much out of the strakes? See attached. If so I was just going to repair it with some woven, if needed. The stringers will also sit in the strakes. Any recommendation on what weight of woven I should use? I turned off all the lights and put a light under...
  15. B

    Replace transom?

    Hi all I have a 1993 crownline that I am working on. Looking for advice on whether or not I should replace my transom entirely or try to repair it in place. The thick part around the key hole seems solid but the outer “wings” of the transom near the bottom of the hull are rotted. I was...
Top