Search results

  1. C

    tach wiring

    Thank you very much.Best diagram I have seen.Your time is greatly appreciated.
  2. C

    1985 150 xp

    Anyone know how to wire a tach to this engine?
  3. C

    tach wiring

    Ok time to wire this boat.what I don't know is how to wire in the tach for my 1985 evinrude 150 xp anyone out there with any help with this one would be much appreciated.
  4. C

    Fixing Up Boat Help

    To be sure,have you had water supplied to the outdrive while running the engine?This is a must.
  5. C

    starcheif transom measurement needed

    sorry did not check the post date.
  6. C

    starcheif transom measurement needed

    I just finished replacing my transom and have the old one laying on a flatbed to reference placement of holes for some items. Would a picture help with a ruler for reference work or would you like me to trace it on paper and mail it to you? Willing to help.
  7. C

    Flooring HELP

    thanks for your help. I am sure I will need more as this goes along. Now for the drill and rivet gun.
  8. C

    Flooring HELP

    There is a piece of aluminum sheet between floor and stringers is this how it was from the factory and how much did it cover? Mine goes from the cabin stepdown to two feet from transom
  9. C

    Flooring HELP

    Very informative article on rivets thank you.
  10. C

    Flooring HELP

    It is NOT 3/4 inch. I believe it was a replacement floor done in the late 70s.I have no idea what was original but everything else is fit to this. It is 1 1/8 thick and I was able to source 1 1/8 marine plywood to replace it.
  11. C

    Flooring HELP

    How would you install solid head rivets? I would like to use rivets if possible.
  12. C

    Flooring HELP

    JB I have already got the 1-1/8 replacement material sealed and prepped to go in. The old stuff was screwed down with stainless screws and I planned to do the same. Had not thought about rivets. Where would I source rivets that long. I do plan to go back in the same holes.
  13. C

    Flooring HELP

  14. C

    Flooring HELP

    That piece came from the aft piece of the deck .One of three. The whole deck is of the same material.
  15. C

    Flooring HELP

    My worry is that the things that are attached to the gunnel and floor would not fit if I changed the thickness. I would definitely like to lose the weight. tite-bond lll it is thanks.
  16. C

    1990 Johnson GT150 wont turn over

    There is a product called OX-GARD that is meant to be used in connectors like the one disgust .I find myself using it more and more because of computer controls. This works very well for me.
  17. C

    Bearing Buddys falling off

    sorry new to this I will figure it out
  18. C

    Bearing Buddys falling off

    I hope this one does not show up twice as the first was a mistake. To peen the buddy in place one would use a very fine pointed punch and strike the shown surface in three places around the buddy leaving an indent about 1/6" round and deep. This has worked without fail for me.
  19. C

    Bearing Buddys falling off

    LOL the second one was by mistake. To clarify to peen the buddy in place one would take a very fine pointed punch and strike the shone surface in three places around the buddy. This should leave a very small indent in the surface but it does work well for me. The indent should be about 1/6"...
  20. C

    Flooring HELP

    Have already done the transom. Removed the old flooring today and this is what was in there. As far as stringers go they are aluminum. Thank you all for the response ,all input is appreciated. In the interest of strength I am thinking I will glue a 3/4 and 1/2 inch ply together to replace the...
Top