Search results

  1. J

    1971 Mercury 4 hp Stator testing

    Does anyone know how to check the stator on a 1971 Mercury 4hp with an ohm meter. It only has one wire coming off the Stator. and a ground screw.
  2. J

    1982 Evinrude 90 hp

    I have a 1982 Evinrude 90 HP that runs fine on ear muffs but boggs down and dies in the water. Any thoughts where i should start to look?
  3. J

    1976 Evinrude 35 hp flywheel issue

    I checked everything and didn’t find anything rubbing.
  4. J

    1976 Evinrude 35 hp flywheel issue

    I thin i have found the issue with my outboard. When i go to crank the motor, cam is turning all the way to the side of the engine. Which is retarring the timing. It acts like its rubbing on the armature plate. I have checked and can't anything rubbing. My question is could my flywheel key be...
  5. J

    1976 35hp Evinrude cranks up and dies out

    On the carb and fuel pump yes. Which wasn’t much
  6. J

    1976 35hp Evinrude cranks up and dies out

    Ok so I thought I would take the fuel pump out of the equation. I hook a clear fuel to a bottle of fuel with an air vent. It still cranked up when throttled up ran 10 -15 seconds and died out. Did that three times. No air bubbles in the fuel. I think I am at the point of checking the intake and...
  7. J

    1976 35hp Evinrude cranks up and dies out

    I am going to do the clear fuel line today. I actually have a new fuel on it now. My fuel pump only has two lines. For vacuum it attaches right to the engine bypass cover which has a hole in the back middle for vacuum. There is a vacuum hose that runs from the bypass cover to the front of the...
  8. J

    1976 35hp Evinrude cranks up and dies out

    I clean it and also the three little holes in the top of the carb. I have clean the carb twice cleaned all the little holes with a snail piece of wire and blew compressed air through it.
  9. J

    1976 35hp Evinrude cranks up and dies out

    Yes
  10. J

    1976 35hp Evinrude cranks up and dies out

    Compression on both cylinders was 120 psi. No I do not know the last time it actually ran right. It was given to me. It looked clean an so far I haven’t found any major issue. I rebuilt the fuel pump and carb. I installed a new water pump , thermostat, plugs, points , coils. Has no tiller...
  11. J

    Setting the spark advance for a 1976 35 HP

    It cranks in full throttle and then dies. any ideas. I rebuild the carb and full pump,
  12. J

    1976 35hp Evinrude cranks up and dies out

    I am having trouble with my 35 hp Evinrude that was giving to me. I have replaced the water pump, thermostat, rebuilt the carb and fuel pump, replaced the points. It will start in full throttle and then dies when I throttle it Back. i am going to pull the carb and clean it again. I am getting a...
  13. J

    Setting the spark advance for a 1976 35 HP

    Ok double checked with an ohm meter and the wires were crossed. The other think I discovered is the remote cables need to be attached so the throttle is in the right position when starting. When doing that is fire over. Thanks again
  14. J

    Setting the spark advance for a 1976 35 HP

    And what am I look for or how do i verify the marks line up? I know then is a mark or 2 lines on the armature plate and time marks on the fly wheel.
  15. J

    Setting the spark advance for a 1976 35 HP

    I would rather not mess with the time, but if the plug wires are not crossed and i don't think they are. That would only leave a timing issue. causing it to back fire and not start. I have a SELOC book on the motor.
  16. J

    Setting the spark advance for a 1976 35 HP

    OK, let me double check that tonight.
  17. J

    Setting the spark advance for a 1976 35 HP

    Just had the motor given to me. It had a bad coil on cylinder #2. I change the plugs. Rebuilt the carburetor and fuel pump. Replace bad vacuum and gas lines. Could I may be putting the throttle in the wrong place when starting? I don't have the remote cables hooked up to the motor. I will go...
  18. J

    Setting the spark advance for a 1976 35 HP

    No and i have fire on both plugs.
  19. J

    Setting the spark advance for a 1976 35 HP

    Looking for a little guidance in setting the timing and or spark advance on a 1976 35 HP Evinrude. I have replaced the points and gap them .020. when i tried to start it I got a back fire. So my guess is my timing it retarded a little.
Top