Search results

  1. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    I wish it were that simple. I should have clarified, massive corrosion. Starter teeth cant keep contact with corroded flywheel teeth. Bad cavities. Apparently this crud had filtered down into the housing & stayed wet for few years. Once the starter spun a few times & cleared out the crud &...
  2. A

    Suzuki DT75 ignition switch & non firing

    Thanks. 10 wires, no ckue which to test, no manual yet. Cant read digital manuals online. Need a lil help on the procedure.
  3. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Project on hold. Flywheel sat in moist debris and rusted teeth so will need engine pull & flywheel swap. I switched focus over to a skeeter with 75hp 2 stroke outboard which has a new set of issues to contend with. Firing stopped and cant find any cdi test procedure. Thanks 4 all the advice on...
  4. A

    Suzuki DT75 ignition switch & non firing

    New project. Has run b4 sitting up for years, fired off with ether then Started basic cleanup/prep for fresh fuel, etc. Noticed #3 plug dead. All 2 Coils r working. Got 3 new NGK OEM. Verified spark. Then, no spark. Early in, ignition switch wasnt making contact. I suspect old grease on...
  5. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    New oil pressure to fuel pump switch ordered. It tested within resistance range but fails to complete circuit when pressurized. Now I know for sure why it was bypassed. All the parts will arrive in a few days, just in time for 2 days of rain. I verified the alternator is marine grade. New water...
  6. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Is the original ignition switch a 4 position or 3 position? The new slave solonoid corrected the no turnover issue. However, I discovered the previous owner swapped an automotive starter instead of marine. New marine starter on order. This automotive starter & solonoid explains the "extra"...
  7. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Great schematic! Where can I find the Identifier key for all the numbered parts? i.e., the oil pressure sensor, etc. I'm going to be wire color tracing & rewiring properly while replacing possible failed/bypassed sensor. Many Thanks!
  8. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Lol, yessir, wire terminal love is on the list. First things first ;) you should've seen it b4 i whacked it with my 2.5 lb thumb waker upper. Terminal will be properly secured soon! Fire BAAAAD!
  9. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Thats important info! What other wire could a mechanic have used on the fuel pump that gives it constant key on power? *the ignition switch is a 3 way switch. I'll trace the existing fuel pump wire color today. Just got notice slave solonoid is delayed, again, and its only 15 mins away in...
  10. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    Thanks. The electric fuel pump is already receiving power when keyed on. And this is happening without the purple/white(or yellow) wire connected. * I should also note its only a 3 node solonoid. *new discovery* slave solonoid has a failure. Will retest if part arrives today. ** Are the...
  11. A

    '95-ish Glastron SSV195 carbureted mercruiser 4.3 starter solonoid wiring color codes

    I'm working on a '95ish glastron ssv195 with Mercruiser carbureted 4.3L. Ser num. F292586. No starter turnover issue. I can jump across starter solonoid & slave solonoid and it will spin. I see 1 purple/white (or yellow) wire near starter solonoid with a round terminal & black rubber cap. I want...
Top