I need the plastic acrylic windshields on the dual console boats. On the full glass and aluminum frame windshield. Just the small plastic ones on each side console.
I am searching for a company that manufactures replacement, to OEM standards, windshields. I have a 2002 Lund Prov 1900 SE. I need the starboard side, but if the cost is not huge, I would buy both Port and Starboard.
If someone can point me in the right direction it would be great. I have...
I used 3 engine lifts that where very shaky and dangerous.
I cut the transom with a Sawzall on a 45 degree angle so i would not cut the splash well. Drilled out all the rivets, and took out the screws in the cabin rear wall holding the Upper and Lower halves together. Then other than wiring...
Reaching out to everyone here that has ever replaced the lower pivot seal on a 1993 Mariner 75hp 3 cylinder. My seal is partially sticking out where the waffle washer is, above the lower mount. I do have the factory service manual, but details on how to change this out when the whole motor is...
I recently purchased a 1993 Pro V with a 1993 75hp Mariner 3 cylinder on it. I have worked thru all the other issues with a motor this old; carb rebuilds, link and sync, faulty coils, new water impeller, new fuel lines, removal of oil injections system, etc....
My current problem is a rough...
Didn't know if it was a spring operated solenoid. and when pressure was back feed, that the valve would open allowing fuel to flow. Thanks for the response.
Also here is more to what I have going on. I pull the plugs last night. These where new before going for an hour total run time, 1/2-5/8...
no the one on top of the carp that the idle fuel mixture circuit is set by. Here;
The reason I am asking, I rebuilt the carbs over the winter, had it out yesterday and set as per the service manual, and it was like 2 turns out when set accordingly. But when coming off plane the motor would...
I have a stupid question for everyone here. I have a 1993 Mariner 75 hp - three carb - motor. I have purchased a Factory service manual and have read all the sections of setting the idler jet screw. It states, initial setting 1.5 turns out, in water, in gear, warmed up, turn in each idler screw...
Has anyone ever added a tell tale water line to a 1988-1991 4 hp Sailmaster outboard. Model number J4RLCCS. I was thinking of drilling the Exhaust Cover plate where the water line passes by it at the top. I was going to use a 10-32 UNF x 5/32 Barb 90 degree fitting. This would only require a #21...
I recently acquired a 1988 Johnson 4 hp Sailmaster (J4RLCCS) that is in near mint condition. I have purchased a factory service manual and have rebuilt the Fuel Pump, Carb, primer/choke system and installed a impeller rebuild kit. I can get it to run great at both Idle and High RPM's.
My issue...
I recently purchased a 1993 Lund Pro V 1775 with a 2007 Minn Kota Power Drive bow mount trolling motor. I have been told by a fishing friend that with the addition of a Min Kota quick change composite bracket, I now need to have a Ram mount head stabilizer. They stated that the head that is...
For those that have been helping me out to resurrect my old 1981-1983 (? Unconfirmed) Honda BF75 from the outdoor rack in the back yard where it has sat for over 7 years in the elements. Thank you for all your help! It is appreciated and this is the place I always come for help. What a great...
Looking for help locating an accessory part for a Pre-1997 BF75 Motor. I have tested the charging circuit on the motor and it is producing power, I would like to buy the accessory plug/cable to be able to charge my battery while I chug along. I have found the block off plug for the motor port...
