Ok, so here is the deal. I am pretty good with engines, but this one has given me the same problem that I can not fix. This is a 2007 mariner 9.9 4 stroke. It will run while the choke is on, and the rpms are up. If you take the choke off then it dies right away. If the engine is cold, 8 hours or...
I have a 2007 21SS and I need a trailer. Well I have a trailer but it does not fit right...
Here is what I need to know can anyone tell me how many bunks are on there trailer how far apart they are and what angle the bunks are at? Also how high are they. This is a Heritage and they make...
Do the spark plug wires thread into the distributor? I was looking at a coil and yoke assembly on-line and it looked like it threaded in underneath the distributor/flywheel. I have never seen that before and I feel like that is a pretty stupid question to be asking?
1970 115hp JOhnson 115esl70d
This weekend I tried to get the old motor started with no luck. So I did a couple things to see what was going on and ran into another issue that may be a little more serious.
Motor: 1970 115hp Johnosn. 115esl70D
First I don't get any spark at any cylinder, I'm going to pulling off the...
So I bought a boat that did not have a motor, this is a project boat and I have never hooked up a motor before nor have I been around enough boats to see what parts are needed to hook them up. So I need to know if there is anything that I need to purchase to hook up my motor and how do I do it...
I recently ran out of resin, and being land locked I have done numerous searches and looking for providers of resin for a reasonable price. I have failed for the most part, however, I think I may have found someone to help me. However I do believe this resin is different then the resin I have...
I am looking for different ways to make My PB for my current restoration. I have read a couple places on what they use just curious what others are using. I am looking for a cost effective method but strong.
What do you have?
I want to make a windshield for my boat but did not know if it is possible to do. I don't care what kinda material it is I just want it to look more modern. Has anyone done this before. Or are you just fitting a Sheild from another boat on your current one. It currently has a walk through, I...
I have a 1997 Heritage tandem axle. I believe it is a 29' foot trailer and gawr is 6000lbs. It currently holds my 18ft bass boat. A little overkill I think but I bought the boat with the trailer, or I guess in this case the trailer and it came with a boat.
Anyone can help me out, as my boat is...
Well I have this 1970 Johnson 115hp motor that I got for my ps3. I thought that was a steal even if it did not run came with boat controls also. So tonight I thought I got all the wires reconnected so I decided to check the compression. Here part of the news
158 158 162 158
I was estatic...
Ok, this is a 1990 ProCraft fish and ski. Im not sure of the first step so I am looking for recommendations. Keep in mind this will be my first restore. I am going to post pics from the ski compartment and transom area. I believe the transom to be 100% solid. I think even the stringers are...
I am going to do a compression check on the engine tonight and I am not sure how to do a jumper to start the motor. I know it needs to connect to the battery but where do I put that wire since it already has a power wire running from the starter solenoid to the battery?
Sorry for such the newb...
On my ignition it says "KF56" I did a search and came up with only 1 key, does anyone know if this is correct. I do not have a dealer anywhere around so I will not be able to go and test out the keys.
On my ignition it says "KF56" I did a search and came up with only 1 key, does anyone know if this is correct. I do not have a dealer anywhere around so I will not be able to go and test out the keys.
