Search results

  1. F

    oil leak on 3.0

    Yoke seal done, U joints greased, and case pressure tested great, trim switches installed and functioning, all trim buttons work correctly (that was a PITA), new timing cover installed, engine aligned for yoke and the drive has been installed and is ready to go. Going to change gear oil with...
  2. F

    oil leak on 3.0

    Yes, I borrowed one.
  3. F

    oil leak on 3.0

    Outdrive was pressure tested. Looking for an alpha one generation one seal kit now. Yoke is out on the bench.
  4. F

    oil leak on 3.0

    Then done for the season…
  5. F

    oil leak on 3.0

    Pressure test showed a pretty good leak. Pulled the yoke out and gonna get the seal kit tomorrow. If everything goes well I will have it back together tomorrow and ready for a dip on Friday.
  6. F

    oil leak on 3.0

    Im going up now to get a fitting for the drain hole so I can put my pressure tester on it. I will do 7 to 10 psi and check for leaking behind the universal joint. The new sensors are done. I verified continuity on wires and spliced new switches on with waterproof fittings as well as triple...
  7. F

    oil leak on 3.0

    I'm having trouble finding the instructions for removing the bell housing. I don't want to just start pulling stuff without knowing what I'm in for.
  8. F

    oil leak on 3.0

    I will pressure test the drive and do the yoke seal, but are the switches able to be installed without removal of the bell housing and bellows etc? I will pressure test drive and do the yoke seal if necessary
  9. F

    oil leak on 3.0

    I removed the outdrive and now am looking at the bell housing. The bellows look like they were replaced not too long ago and look new. Can I install the new trim switch/sensors without removing the bell housing, bellows etc? I'm really having a tough time finding some clear information/videos on...
  10. F

    oil leak on 3.0

    I pulled the drive off see oil and grease inside the bellows. I’m going to remove the rest of the unit tomorrow so I can change the bearing and install trim switch/sensor, but I’m curious as to whether there should be oil in the bellows? Thanks
  11. F

    oil leak on 3.0

    Thanks!
  12. F

    oil leak on 3.0

  13. F

    oil leak on 3.0

    I am going to get a bar and make sure it’s all squared away. Any thoughts on how to determine whether I have an alpha 1 or 2? Generation 1 or 2?
  14. F

    oil leak on 3.0

    I thought about a repair but when I looked it over I figured it was best to replace it. I’m going to make a concerted effort the keep it clean and dry
  15. F

    oil leak on 3.0

    I will go thru the drive and install new trim switch/sensors when I do that. I will have a little more peace of mind knowing its all squared away come next season.
  16. F

    oil leak on 3.0

    Ok, that sounds fair to me. I’m happy is didn’t have to remove the engine so that’s a fair trade off!
  17. F

    oil leak on 3.0

    Even though the motor was only lifted literally 1/8”? I have the original position on the mount marked for re installation. I only raised enough to take the load off the mount.
  18. F

    oil leak on 3.0

    cover is off and I ordered the NAPA timing cover that crosses to the dorman number for automotive applications. the part is NLA according to the local Merc dealer. I don't see why the part won't fit but who knows till it gets here. Engine still in the boat, took out bench seat and placed a 2x4...
  19. F

    oil leak on 3.0

    I think that’s probably the way I will go. I will put some type of sealer or rust proofing on iota and it should be fine I would think
  20. F

    oil leak on 3.0

    I’m looking for a timing cover and gasket kit as well as a seal kit for the outdrive so I can get started on the project. The outdrive inspection will be a good thing and I have to change the trim switches too.
Top