Search results

  1. B

    1968 9.5 IDLE ADJUSTMENT knob

    Been reading up on that and other problems. Big seal looks good but will see. The foam is a good idea. The water tube to block sounds like a nightmare so hope it's good. Forgot the IMPELLER HOUSING seal 031000 so hope it's good as well If tube stays put will try running it and hope i get a...
  2. B

    9.5 johnson motor tag gone

    it's been duckofloged
  3. B

    1968 9.5 IDLE ADJUSTMENT knob

    going to take the gear case off today and check/clean impeller housing and plate. have the impeller but the water tube seal should be here later today or tomorrow plus others
  4. B

    9.5 johnson motor tag gone

    After checking on other parts i see the front panel is at least 1969. this welch plug give any clue?
  5. B

    1968 9.5 IDLE ADJUSTMENT knob

    motor got the duck hunter treatment sometime in the past. that part came from a part seller. 9.5 came on a Lund snipe I've been fishing out of with 3hp Evinrude that runs like a sewing machine thanks to this site. 9.5 had around 75 psi per cyl when i checked it before buying, and it started...
  6. B

    1968 9.5 IDLE ADJUSTMENT knob

    well the knob is held in with a tiny snap ring so will have to remove the bracket assembly no matter what to reinstall. thanks crosbyman you got me on the right track. And this motor is 1969 or newer i believe now, threaded piece is part #62
  7. B

    1968 9.5 IDLE ADJUSTMENT knob

    Not sure if threaded part is in my motor. was hoping i could remove knob from part i bought and screw it in mine but don't think it works that way and haven't got the replacement knob out. Here it is with threaded part slid off.
  8. B

    1968 9.5 IDLE ADJUSTMENT knob

    thanks, think this is your pic Crosby
  9. B

    1988 Evinrude 4hp

    25 lbs is dismal, new head gasket?
  10. B

    1968 9.5 IDLE ADJUSTMENT knob

    Motor runs but waiting on impeller parts. My knob is missing but bought a used BRACKET AND FUEL CONNECTOR ASSEMBLY with the knob (0380892). The knob has square shaft that threaded shaft fits over it from inboard side. threaded part is not in any diagram i can find but i have it. Dose this work...
  11. B

    where to buy spark wire and good fuel line

    This work for older outboards? https://www.iboats.com/shop/brp-7mm-ign-wire-1-foot.html
  12. B

    where to buy spark wire and good fuel line

    thanks, never tried that, always use the solid copper core.
  13. B

    where to buy spark wire and good fuel line

    only place around here wants $6 a foot for wire
  14. B

    9.5 johnson motor tag gone

    it probably 67 or 8. Johnson MQ-14D
  15. B

    where to buy spark wire and good fuel line

    I need to replace fuel lines on a couple 1967 3hp evinrudes and a 9.5 1967-8 johnson. The Johnson has a few different size lines. And need some plug wire and ends for both. Solid copper core 7mm works for both i think but where can i get it? Going to Napa and match up fuel line and get some...
  16. B

    9.5 johnson motor tag gone

    Always had 3-4 hp omc's, first twistshift i owned. got an order for parts started, still adding. pretty sure its a 1968 Evinrude 9822D
  17. B

    9.5 johnson motor tag gone

    thanks will do.
  18. B

    9.5 johnson motor tag gone

    Thanks, repainted hood and all stickers gone. But checking part no.'s it is 67 or later so can figure what i need. But I'm kinda stuck about impeller/cooling. Since this has a thermostat how long should i run it before it opens up? Ran it about 30 seconds and shut it down with no water at all...
  19. B

    9.5 johnson motor tag gone

    Anyway tell the year without the info tag? i know it's 6?-73 era. does it matter buying parts , not sure how many changes in those years
  20. B

    attwood 9300FDV7 Universal Fuel Demand Valve

    Thanks, only reason i bought this tank it had a vent screw on the cap so I'm good! long as i remember to use it!
Top