Search results

  1. K

    Low Voltage to the Ignition Switch

    Try unplugging the main cannon plug, then carefully spread each male pin, sometimes that is all that is the problem. Also try to inspect the main harness from front to rear, I once encountered a drill hole in the harness from when the rub rail was installed. Be sure that every wire terminal...
  2. K

    Volvo Penta 40 / Archimides 40 / Solo 40. German engine manual/help

    If the piston is seized take out the spark plug and fill the cylinder with automotive brake fluid. I learned this from a motorcycle collector who has good luck freeing up motorcycle engines.
  3. K

    Mercruiser 888

    You can get the correct Holley marine carburetor from Flying Fish Carburetors. Contact them and they will be able to explain why your engine is not performing correctly. They also may be able to jet the carburetor to compensate your altitude. Also tell them which cam you are using. Do not get...
  4. K

    Mercruiser out drive compatibility

    Do both drives power trim or just power tilt? Power tilt models used a setting pin and a mechanical lock on the drive. And power trim models used a hydraulic lock valve. Power tilt drives will work on a power trim boat but a drive from a power trim boat will not stay down in reverse unless you...
  5. K

    Mercruiser 888

    What elevation in regards to sea level are you? Is your carburetor the correct marine 2 barrel Holley version? Are you sure that your boat does not have water or mud trapped inside? I once had a customer who bought a boat that must have sunk at one time and it had mud trapped in the double...
  6. K

    Mercruiser 888

    Ford went to the 13726548 for a reason. The hp gain must have had something to do with the firing order and increased durability. The same engine had 225 hp with a 4 barrel. You will most likely never get the torque in the right rpm range that the original cam profile delivered. I am no...
  7. K

    Mercruiser 888

    What is the firing order of your engine?
  8. K

    1968 Crestliner Buccaneer w OMC Inboard 80hp

    This engine also came in Ford Pintos 1600 cc. In my humble opinion he should just drain the oil from the drive and if there is no water then just refill it. Pulling that drive apart to reseal it if it does not need to be done is flirting with disaster.
  9. K

    Connecting spline sleeve

    Contact a Marine surveyor and your attorney. Get some estimate/opinions from other Volvo dealers.
  10. K

    Connecting spline sleeve

  11. K

    Bravo 3 steering cable stuck in housing

    It looks like water is draining over the area probably from the engine hatch. Try to seal the area or make a shield to direct the water past the steering system.
  12. K

    1990 Rinker 18.6

    Thanks Bondo, my bad. A good thing I am not a lawyer!
  13. K

    1990 Rinker 18.6

    If the rotor is not turning while the starter is turning the engine over then there are a lot more problems internally in the engine.
  14. K

    New purchase SX-M

    I sent you a PM. Let me know on the site if you got it.
  15. K

    New purchase SX-M

    How about using a few pounds of compressed air instead of water? There also might be a vent hole in the top of the housing that you will have to plug. A piece of aluminum the diameter size of the pivot housing end with a schreader valve and a plug in the bearing should work. Then with some...
  16. K

    New purchase SX-M

    I have repaired a few Mercruisers with the housing either damaged or eroded away. First remove the stiffening wire from inside the bellows if there is one. Turn the bellows inside out, this makes it easy to grind off the raised bead. Reverse the process and put it back together. Just be sure...
  17. K

    OMC 140hp with 400 stringer sterndrive lots of questions!

    Did you replace the solenoids with the correct marine style? Most marine solenoids are “non grounded base”. Also marine solenoids are sealed so they will not create a open spark. Is there power to the battery side of the solenoids? There are two 50 amp fusees, 1 powers the instrument panel...
  18. K

    I have a leak.

    It might be one of the sacrificial anode bolts, they can be replaced without removing the engine. my bad with the key board.
  19. K

    I have a leak.

    It might be one of the sacrificial anode bolts, they can be replaced without removing the engine depending on how the boat is built and how flexable your body is. Otherwise the engine needs to come out.
  20. K

    1987 3.0L water in oil

    Usually there is a pinhole near the rear of the block on the bottom of the water jacket. That is the thinnest part of the casting. If you have an engine stand fill the water jacket with water then blow air under the jacket area and you will probably find the leak.
Top