Search results

  1. K

    Starter wont engage flywheel.

    Check if there a spark coming out the coil wire at the distributor cap to ground.
  2. K

    Vortec 350 Removal in an AZ220DB 2007

    Post a picture. First, remove the drive then the electrical, then fuel, be sure to plug the fuel line after it is disconnected. Then power steering pump, throttle, water, exhaust hoses stringer lag screws, the 2 self locking nuts behind the flywheel housing and it should lift straight out. Do...
  3. K

    Starter wont engage flywheel.

    Since this is an inboard reverse entry starter are you sure that you have the correct starter for your engine’s rotation? When you first tried to start the engine with the original starter and it would not engage did you bench test it? If there is any rust build up on the starter shaft in front...
  4. K

    1988 Dixie Boats 170 Bandit Alternator?

    That is all you need. The alternator self excites it self by just punching the throttle 1 time for it to start charging. Just tape off the unused leads.
  5. K

    Head Gasket

    Sierra Marine # 18-2946. Head gasket # 18-0164. Thermostat housing to head gasket # 18-0347 Valve cover gasket # 18-1204. Manifold to head gasket This should be all you will need. If the head gasket was blown out from...
  6. K

    What causes this knocking tapping sound?

    Is the noise the same with the boat in the water and in forward gear ?
  7. K

    1988 Dixie Boats 170 Bandit Alternator?

    Is it a1 wire alternator? IF it is then a Sierra Marine# 18-5956, no core required. The original alternator probably had an exterior regulator. The 1 wire style has it internally.
  8. K

    What should I check on OMC Sterndrive?

    Get the genuine OMC service manual for your model and not the “bootleg” one.
  9. K

    O-Ring Re-use and/or part numbers

    I do remember those “O” rings and they sealed the hole where the bolts came through the transom. If you cannot find replacements just reuse them with some 3M 5200 or a similar compound. Also I used to just flip the large rubber rings that insulate and seal the PDS housing and never had a leak...
  10. K

    1980 ChrisCraft 170SS freshwater pump

    Looks like a Sherwood pump. If so it will have raised letters on the backside of the cover.
  11. K

    ESA module location

    If it is there it would be right near the carburetor with some blue and grey wires coming out of it. Try to post a picture of the top of the engine.
  12. K

    VP 280 Engine Alignment

    If you are in doubt then try to hang the front of the engine with the engine hoist. Or a small jack under the engine. Then loosen the mounts and raise and lower the engine easily to set the alignment. This saves a lot of time instead of turning the nuts to set the alignment.
  13. K

    Hose laying in bilge

    Flywheel housing drain in case bilge water gets into it.
  14. K

    VP 280 Engine Alignment

    Just bolt the whole thing together Into the transom plate. Then with either the diameter of a pencil eraser or similar item use that as a gauge around the outer perimeter of the mounting collar to the transom plate. That will properly set the alignment.
  15. K

    4.3L OMC Cobra 1988 engine knock/rattle

    Does water come in when the boat is in the water without the engine running?
  16. K

    5.7 alpha knock please listen

    It sounds like something in the flywheel housing.
  17. K

    2007 Volvo Penta 5.0gxi - no compression in # 4 cylinder

    If you are handy with the tools just pull the head in question. Most likely the piston is not damaged enough to cause any problems. The head can be brought to any engine machine shop who can check if the head is still usable or not. You may have a manifold with an internal leak so plan on a...
  18. K

    Lean Popping on Accleration

    Sometimes spark plugs will act like that. You may have an exhaust manifold that is leaking internally. Before you start the engine after it has sat for some time remove the spark plugs and look for moisture.
  19. K

    Mercruiser 383 Mag Stroker MPFI Bogs Over 3000 rpm

    There is a switch on the shift linkage plate that prevents the engine from going over a certain speed if the shift is in neutral, sometimes that is the problem. It is there to make sure that the drive is fully engaged. I am sure someone on the site can post a picture of the switch and possibly...
  20. K

    Should I grease upper gear case housing before install?

    I always would slightly spread the split ring open to make sure it is holding the shims in place. If the split ring was first it would allow the shims to fall and get damaged while installing the driveshaft.
Top