Search results

  1. K

    Trim pump

    Does the pump run?
  2. K

    Volvo Penta 3.0 GLP Stalling when reducing from high RPM.

    The only other thing that I have seen cause this problem is the rotor in the distributor. What happens is as the boat is coming off plane it puts a load on the ignition and the high tension spark goes through the rotor to the distributor shaft.
  3. K

    1985 Sea Ray Mid Cabin

    Try filing the points or just replace them. Ignition points build up some corrosion from long storage. If you do buy a set be sure to buy them from NAPA. Set the gap .016-.017.Stay away from those “big box” auto stores. If you decide to convert to electronic here are the Prestolite kit...
  4. K

    1986 5.7 upper gear case shim question?

    The thing I liked about the stern drive repairs is the shimming tools. With those you knew it was right. Is the gimbal bearing good?
  5. K

    1986 5.7 upper gear case shim question?

    That is going to be the best way. Just be sure that you can feel some “back lash”. Just like a ring and pinion. Too much will use be a little noisy but you know what no “back lash” can do. When filling the drive there is a vent screw mid point on the side of the lower gear case, when the...
  6. K

    1986 5.7 upper gear case shim question?

    The joints r&r just like a auto drive shaft. To ease your mind just replace the the shim with the same color that was there before. And it will be good. I had all the special holding fixtures for the stern drives. They are just a real PITA to work on without them. Clamp the drive on a...
  7. K

    1986 5.7 upper gear case shim question?

    Under the front bearing retainer where the shims go. That is where you place the feeler gauge while holding pressure on the retainer. Once you figure out the clearance select the shims and subtract .002. The rear bearing cup is what sets the back lash. The shims provide the preload on the bearings.
  8. K

    1986 5.7 upper gear case shim question?

    Does the inside of the drive look as good as the driveshaft?
  9. K

    1986 5.7 upper gear case shim question?

    You should get a genuine OMC Cobra service manual. I like the video. Why are you taking the gearcase apart?
  10. K

    1986 5.7 upper gear case shim question?

    The plastic shims under the input retainer are for setting the pre load on the input shaft bearings. Used bearings are happy with 6-8 inch lbs of rolling torque. Without the shims hold the retainer tight against the bearings, measure with a feeler gauge under the retainer, then subtract 2...
  11. K

    Exhaust noise SX drive

    The perforated bellows might be the best for noise reduction with restrictor under the zink plate.
  12. K

    Exhaust noise SX drive

    The reason for the exhaust relief was to help larger boats to get on plane. If you do restrict the relief it may also affect your planing speed. Just try it out.
  13. K

    OMC Stringer ESA not working-Adapter housing not centering.

    Remember what I stated in post #2. There are some special tools that are used to remove and replace the small pin male/female connectors. You did the best thing by removing the connectors. Now there is no doubt that the connections are good.
  14. K

    Volvo Penta AQ125/270 overheating raw water not pumping

    You can also remove the suction hose from the through transom fitting in the boat then submerge it in a bucket of water. That way you will know if the pump is working.
  15. K

    tilt light stays on

    Where the screws protrude through the bottom there is a raised area on the tilt housing, 2 nuts go under the raised area to hold the housing down.
  16. K

    1998 Volvo Penta 3.0 misfiring on plugs 3&4

    Your exhaust manifold riser could be the problem leaking back just enough exhaust water to foul the spark plugs.
  17. K

    1978 SkiSprint w/ PCM 302/BW 10-17 transmission. Dies when put into gear.

    Most likely the clutch plates are rusted together. Pull the transmission and have it rebuilt.
  18. K

    Front engine mount wont go low enough to align gimbal bearing

    I had to keep a cut down mount in stock because the Galaxy boats usually had the front too high which was caused by the “X” dimension too low. And also Mercruiser did make a “short” front mount at one time. As Chevyls6 stated in #8 that he had replaced the front mount and it may be too high.
  19. K

    Raw Water System Cap Leaking

    If you are loosing anti freeze coolant from the heat exchanger side then get a 125 Volvo service manual. You have a leaking head gasket. When the cap starts leaking does the temperature go up? When the boat is on plane at full throttle there is more water flowing through the exhaust manifold...
  20. K

    Front engine mount wont go low enough to align gimbal bearing

    If the transom is not rotted then what may have happened is the hull has settled just due to the age. The easy fix is to remove the front mount and have a welding shop cut and re weld 1” out of it. Also a very good chance that the rear mounts should be replaced.
Top