Search results

  1. K

    Old ford 302 no spark

    Since you had 12volts going straight to the points and condenser there is a good chance that the spring that closes the points has lost it’s tension by over heating and the condenser is cooked. At this point you should convert to a Petronics electronic conversion.
  2. K

    3.0 litre Mercruiser sterndrive oil issue

    Go to a contractor style plumbing warehouse or if you have a plumber friend. They will have the correct extractor. Probably the smaller sender was for a light on the instrument panel or a alarm like Scott06 described that lets you know the ignition is on and the engine is either not running or...
  3. K

    Old ford 302 no spark

    You had me scratching my head for awhile. Yes you do have a Mercruiser harness. There is either a circuit breaker or a fuse where the #10 red wire is connected to the solenoid on the trim pump.
  4. K

    Volvo Penta 5.7 GSi PLKD timing mark out of scale

    I am not familiar with your wiring harness but try checking if you have 12 volts at the +or bat side of your coil while in cranking mode. I realize this has nothing to do with the timing but might help in starting. Is the fuel pressure present while cranking also?
  5. K

    Old ford 302 no spark

    How many wires are connected to your alternator? Mercruiser engines at one time had 1 wire alternators like AD posted. I think you have a OMC engine that used Prestolite alternators which have a remote mounted regulator. Post a picture of your alternator.
  6. K

    high vs low profile

    Since you already have a electric drive what is wrong with the current one? The bottom gear housings are identical, it is the exhaust housing that can be swapped over if that is the problem.
  7. K

    high vs low profile

    77 was the last year for the electric model and 78 was the hydro assist model. Even with the hydro assist the V8 models started jumping out of gear right away. OMC found out the hard way on that set up. While it worked for out boards they finally figured out that the V8 s smooth idling was...
  8. K

    high vs low profile

    Actually it will bolt on however you will have to convert the shift to electric and the original shift cable hole needs to be plugged and a hole drilled in the opposite side of the intermediate housing, and of course the extra length will surely prevent the boat from planing off plus the drive...
  9. K

    New Engine Replacement - Engine Died and Hydro locked after 5 hrs!?

    The third bellows might be the one where the shift cable enters the hose that guides the cable to the drive.
  10. K

    3.0 litre Mercruiser sterndrive oil issue

    If the oil filter was rusted badly enough that may be what made the noise you heard when it blew out.
  11. K

    Replace Teleflex or go hydrolic?

    Google Panther Marine Troll master. They make remote control steering, throttle and shift wireless controls for all popular small outboards.
  12. K

    4.3 omc cobra no start

    There is something else to try, get a jumper wire and connect the + or Bat side of the coil to a constant 12 volt source, spin the engine over and check the color of the spark. Your problem may be the ignition by-pass circuit in the solenoid. In the meantime try to get a dwell meter. If you...
  13. K

    302 distributer

    Chris , I stand corrected on the MM distributor application. I am glad you was able to find the application. I did not know that MM made distributors, the reason I described them was from the Holley distributors used in the fleet of International Harvester trucks that we serviced at my Dad’s...
  14. K

    302 distributer

    That is a Holley. One way to tell is the small split in the base of the mounting plate near the contact points. You might have to contact Petronics as I could not find a Holley kit listed in the Sierra catalog.
  15. K

    302 distributer

    There are 4 different distributors used on the Ford 302-351. Mallory, Pertronics, Ford & Holley. Most common are Petronics & Mallory. Post a picture of the points and then we can tell which one you have.
  16. K

    Is it worth it?

    One thing worth checking is if there is excessive wear in the distributor. Remove the plate and check that the weights, springs and slop in the shaft upper bushing. There is a bushing in the block that supports the lower end of the shaft which wears out. The easy cure is to add a bushing to...
  17. K

    1970 OMC CUFM-69B Impeller access

    When you get the service manual and I hope it is a GENUINE OMC, you will see the drive being worked on mounted in a special holding fixture. Without them it is a real PITA to work on. I have performed this many times, for you I suggest first drain the upper gear housing. It is not necessary to...
  18. K

    Volvo Penta AQ140 water coming out of carbs.

    The replacement engine looks good from the outside. Those are tough engines and give a lot less trouble than the later models. I hope you got the PDS housing with it. Good luck.
  19. K

    New gimbal bearing, can’t get alignment tool in coupler

    To check if the rear engine mounts have collapsed is with a sharp pick try to rotate the insulators on both sides. If you can move them the mounts are still good. One reason why Mercruiser wanted the open side of the gimbal bearing carrier facing forward is someone started selling just the...
  20. K

    5.0GL - No Power at Coil

    Try to get the original one rebuilt, 120 amp would be good if you had some high dollar sound system in the boat. You should be able to find a rebuilder in your area.
Top