Search results

  1. 04fxdwgi25

    Shift interrupt switch - how to adjust??

    The Alpha drive service manuals have every detailed adjustment instructions.
  2. 04fxdwgi25

    Reliable sure lube hubs

    One problem with the ones that bleed into the axle is, the grease nad harden / plug up in the hollow axle tube over the years, 1. Pumping grease in will blow out the seal or push the cap off 2. When the grease heats up and expands, due to nowhere to go against the full / hard grease in axle...
  3. 04fxdwgi25

    1995 Chaparral 2550 SX Refit and Restoration

    OK, now you have 3 of them. I am starting to think you are a hoarder, there Drew. Where in NC did you find that one? I an in the NE of N, 90 min for the outer banks, on the Chowan River.
  4. 04fxdwgi25

    1995 Chaparral 2550 SX Refit and Restoration

    Nice pics Too bad about that windshield. Will be "spensive" to replace, IF you can find a replacement.
  5. 04fxdwgi25

    Trim Tab relay location

    Bennett trim tab pump. Self contained with solenoids under the smoked cover and no external relays. Dash switch for trim tabs tell pump where to send the fluid to the tabs and how. There are check valves under the solenoids (they just unscrew) that do get gummed up and mess up the operation...
  6. 04fxdwgi25

    4.3 runs great for about 30 minutes then bogs, pops won't accelerate

    I think reading the service manual may have been of some help, too..... Just spit balling here.
  7. 04fxdwgi25

    Trim tab pump and control

    Here is what I believe should be: Also, Add some shrink tubing over those diodes / connections to prevent short circuits and bigger problems Also again: Make sure that port connection for hydraulic line is securely plugged on front of pump.
  8. 04fxdwgi25

    Trim tab pump and control

    That red wire from the Bennet should not be connected to anything. The red wire from the ProTrim should go to a 20 amp fuse powered from the battery. The voltage drop comes from that Bennett red wire circuit goes through solenoids. That is where your problem lies, me thinks. I will make a...
  9. 04fxdwgi25

    Trim tab pump and control

    I see what is going on here. Here is the ProTrim diagram. The green is down (deploy) and the blue wire is up (retract). If either the up or down are powered, the diodes power the stbd circuit. Green from the ProTrim is down - connected to pump blue (deploy) Blue from ProTrim is up - connected...
  10. 04fxdwgi25

    Trim tab pump and control

    Disregard what I posted earlier. That assumption was not correct.
  11. 04fxdwgi25

    Trim tab pump and control

    Here is what the colors are for on the Bennett System: I have yet to find the wiring for that ProTrim switch to try to figure out what was exactly done using the diodes.. It would seem as though the proper way would be to disable either the port (red) or stbd (green) circuit and use the...
  12. 04fxdwgi25

    Trim tab pump and control

    I haven't figured out the reasoning for the diodes. Need to find the info on that controller.
  13. 04fxdwgi25

    Lowering the bunks . . .

    Does your trailer have target bunks for the front part of the keel on the front? Could you possibly use a loner trailer tongue? I have seen tongue extensions that are used for shallow launch ramps to get trailer out deeper.
  14. 04fxdwgi25

    Lowering the bunks . . .

    OK, I see what you were saying. When you mentioned launching and retreiving, sounded like when backing down the ramp. If you have discs, the bleed off / block valve (connected to the back up lights) may be malfunctioning, preventing the surge coupler from applying the brakes is where I would...
  15. 04fxdwgi25

    Mercruiser trim pump issue

    The creaping back up may be air in the system. The dash meter jumping thing is normal when engine is running and there is a drain on battery from high electrical load being used.
  16. 04fxdwgi25

    Lowering the bunks . . .

    When you say you see much braking in launch or retrieval, are you questioning brake action when backing up? Please disregard if I read that wrong. There won't be any braking in reverse with surge brakes. I eliminated the surge coupler and went with EoH to have braking in reverse.
  17. 04fxdwgi25

    Popped through the intake.

    How old is the fuel? Has the fuel / water separator been changed? Take a fuel sample and see if there is any water in it.
  18. 04fxdwgi25

    Bravo shifter / throttle install on a gen 2???

    What boat / engine ( I see it's an Alpha gen 2 ) we talking about here. A little clarity will go a long way. Pictures of what you have vs what you want help too. We are basically guessing here. Are you talking about cables when you say replacing a "alpha style" with a "bravo style"? 99.9%...
  19. 04fxdwgi25

    Thunderbolt IV 4'' box module wiring

    Since you provided very little to no info on what you actually have, here is the general Thunderbolt 4 wiring, as requested. This is an Alpha. Bravo is same without the cut out switch. I would ground to a bolt on the intake or block, eliminating at least 3 possible joints / points of failure...
  20. 04fxdwgi25

    Dust Cap Woes

    Let's go about this in logical steps. I am curious, as I have never had a cap fly off a hub on any vehicle or trailer. Can you take a measurement of the ID of the hub, where cap sits, with a caliper and post what it is. Then post what the OD of the cap is. Either the hub is out of spec, or the...
Top