Search results

  1. harringtondav

    Aq 151a winterize first time. No water came out

    I'm also unfamiliar with your VP. ...only VP experience is my 2022 4.3. Mine has a single point raw water drain that seems to work well. Manually draining the block, exhaust manifold(s) and the raw water pump outlet to the HX basically does the same. My OM specifies closing the single point...
  2. harringtondav

    Broken Skeg Tip...Repairable?

    Every O/B or stern drive has a skeg. Reasons? Prop protection for sure. Kinda like the "wing ding" curb finders in my pop's '56 Rambler wagon. Early warning when you're getting too close to the bottom at slow speed. I've never replaced a skeg. When I've had pile ups I do it right. New lower...
  3. harringtondav

    Broken Skeg Tip...Repairable?

    Most prop repair shops can repair it. Either by welding the tip back on, or building the skeg back up and shaping it. ...second is the best repair.
  4. harringtondav

    How to Remove Brass?

    I have a unopened cartridge of Merc 2-4-C with teflon (PTFE) plus a gun half full of the stuff. Best prop shaft grease in my mind. Waterproof and always on the splines when I pull my props. Also great for prop thrust plates, gimbal pivot pins or any other under water joints. I've gone VP now...
  5. harringtondav

    When You've Reached the End of Twofootitus.....

    ....Maybe
  6. harringtondav

    Chap Quality Control is gone

    I was down to the Chap 19' BR or the Regal 1900ESX when I bought our new boat two years ago. We went with Regal. Chap only offered a 190 hp Merc 4.5, Regal offered a VP V5 4.3 250 hp for a modest cost. What sealed the deal was VP's fresh water HX cooling with a good single point raw water dump...
  7. harringtondav

    Hub repair

    Many posts here about pinning, bonding the hub to the prop bore. Hubs are designed to slip for a reason: To protect the prop shaft and L/U bevel gears. Bypassing this has risks. I guess your decision is whether a new prop is worth more than your old motor. I'd check out the availability and...
  8. harringtondav

    Re-thread 2000 VP SX-M cylinder for hydraulic hose

    High pressure steel lines seal at the flare at the end of the steel tube. The straight thread flare nut on the tube doesn't seal. It just forces the tube flare on the male seat in the housing with enough force make a metal/metal seal. Before you put a tap into the cylinder you need to know the...
  9. harringtondav

    Glastron contact details?

    Glastron is still producing boats. Contact info below. I believe VEC hulls were short lived. Glastron and Larson VEC boats were built in the same Genmar factory. Larson died off several years ago. I hope you have some luck getting a repair. https://www.glastron.com/us/contact
  10. harringtondav

    Rattle when in gear

    Picking up on @QBhoy 's comments. The trim anode is unnecessary with power assist steering. Flush anodes are available and will prevent this and trash/wood getting caught and bending your prop. Easily changed. Pop the plastic hole cover and use a 3/8" drive 1/2" socket with a longish extension...
  11. harringtondav

    Rattle when in gear

    Your outdrive must be filled from the bottom up. You'll need an inexpensive lube pump. Remove the bottom filler screw per @nola mike above and see if any lube, and anything else drains out. Attach the lube pump, remove the vent screw above, and start pumping lube until it dribbles out the vent...
  12. harringtondav

    Steering tight/hard to turn when i turn right

    Stating the obvious here, but you have a leak in the power assist somewhere. .....something else for you to check periodically.
  13. harringtondav

    VP SX Cone Clutch Question

    I recently changed my prop. New prop was a Solas RubX hub. I was unable to get the std cotter pin through, and I was trying to over torque the nut hoping to squeeze the hub as rearward as possible after I drove the hub in with wood blocks and a 3# machinist's hammer. Too lazy to find a block for...
  14. harringtondav

    BRP Horizontal Engine?

    Previous post on this topic is closed, so here is an update on BRP's SeaDoo Pontoon. I've seen this in our pool a few times. I suspected it was equipped with the new BRP submersible motor, but their page seems to show a traditional Rotax inboard. Not a bad price for a 16', 130 hp pontoon @<$25K...
  15. harringtondav

    Oil pan drain hose

    My pal has one of these and has let me borrow it. It's a bit pricey, but works great. I'm prepping to buy my own. https://www.pentair.com/en-us/products/residential/water-supply-disposal/recreational-vehicle/shurflo-oil-change-winterizing-system.html
  16. harringtondav

    trailer makes banging noise when stop & starting

    I've had this over the years depending on the boat/trailer and tow vehicle. As near as I can tell it's has to do with coupler slack in the hitch ball. So make sure your tongue weight is adequate. Obviously make sure your hitch ball isn't too small for the tongue coupler. Make sure your tongue...
  17. harringtondav

    Should I replace my surge brakes with electric on my boat trailer?

    I guess that explains the rotted lines. I changed the same front caliper three times until I realized the flex hose feeding it had collapsed on the inside. Pressure would activate the caliper. The crud prevented it from releasing. Advance replaced the calipers on warranty. ....I bought the hose...
  18. harringtondav

    Should I replace my surge brakes with electric on my boat trailer?

    I installed electric drum brakes and controller on my previous boat/trailer. They worked well. I liked the adjustable gain and manual activation control. ...also no back up lock out or solenoid needed. I liked them enough that I wanted my new Shoreland'r trailer to have them. No go. Surge disc...
  19. harringtondav

    OK to Delay Recommissioning One Year?

    I was just a sprat at the time, but I knew a guy who had a 67 or 68 GTO. He could smoke the tires in each of the four gears, with front lifting a bit off the line.
  20. harringtondav

    OK to Delay Recommissioning One Year?

    I know. Time was short when I put it away so I fogged it with premix gas, drained it, ran antifreeze through the raw water side, dumped the antifreeze, and called it good. Was planning on getting a Shurflo or Jabsco oil extractor this spring to simplify the oil change. Depending on when the big...
Top