Search results

  1. Alumarine

    oil leak on 3.0

    How did you remove the retaining nut, do have the tool?
  2. Alumarine

    oil leak on 3.0

    If it's oil and not grease then you need to pressure test the drive. You might need a new yoke seal and maybe the yoke as well it it's worn.
  3. Alumarine

    ATV and moving boat around on stone

    Did the same with a 12hp for years.
  4. Alumarine

    Sunrunner 320 classic (1990)

    Welcome. Your best bet is to get genuine volvo manuals for the motors and drives. There won't be a manual for the boat. You will have to google for info on some of the systems in the boat. Or you can ask questions here as well.
  5. Alumarine

    Main engine for trolling

    Sorry I don't have an answer for you but hopefully someone will come by with a good answer. I'm not sure why your engine builder would say not to let it idle.
  6. Alumarine

    3.0 timing

    Then it's a 3.0L and your serial number 0D445400 is probably correct. Manual 13 part no. 90-816-462
  7. Alumarine

    3.0 timing

    If that serial number applies to that motor then you need manual 13. That series came with points or electronic ignition. Did you look for a number stamped by the distributor?
  8. Alumarine

    3.0 timing

    That number isn't quite right. There should be a serial number plate with something like 0C856451 or 7 numerals If that's missing, then the engine code is stamped on the block by the distributor.
  9. Alumarine

    3.0 timing

    Do you have a serial number for that motor? If it's a newer 3.0 then points gap is .016" timing is 8 degrees BTDC at 650-700 rpm and dwell is 39-45 If it's an older 3.0 then points gap is .022" timing is 6 degrees BTDC at 650-700 rpm and dwell is 28-34. Setting the points gap will get you in...
  10. Alumarine

    Trim

    There was a good video be achris on how to do that in the stickies but I can't find it. edit - After looking through your thread I just saw you have a Bravo. Don't know if the video applies to them.
  11. Alumarine

    Trim

    Have you tried rotating the trim gauge sender to adjust the gauge reading?
  12. Alumarine

    Trim

    ?????
  13. Alumarine

    Trim

    "You know what…I just thought about something…do I have to have the 2 senders that mount on the side of the drive installed? They're just hanging there." If you don't have the senders connected that will stop the trim up from working properly. The trailer up will not be impacted by having the...
  14. Alumarine

    No spark, 91 536

    Did you have it running before you changed the ignition parts?
  15. Alumarine

    Battery low alarm

    Try wiring the Humminbird directly to the battery if it isn't already. If that solves the problem, you have a wiring issue.
  16. Alumarine

    91 stingray 536 zpx tune up

    Ah, I missed the 91 part in the subject line. Was just going by his request for /cap/rotor/points.
  17. Alumarine

    91 stingray 536 zpx tune up

    If it is the points type distributor how do the points etc. differ from the auto ones? I've been using that type for 40 years. No explosions so far!
  18. Alumarine

    91 stingray 536 zpx tune up

    For those ignition parts try a 1964 Chevy II 4 cylinder. Different motor but parts should work.
  19. Alumarine

    Can I install a newer outdrive?

    Looks like it goes to 14 lbs so that should work fine. Here's a link from the stickies. https://forums.iboats.com/threads/drive-pressure-vacuum-check.230980/
  20. Alumarine

    Can You Make Up For Different Gear Ratio With a Different Pitch Prop?

    With your 140 it would be difficult to find a prop small enough to work with the 1.50 drive. You should put your engine and boat info in your signature.
View older results
Top