Search results

  1. M

    Listing to port side

    Might want to read all the responses before chiming in . Post # 12 gives you the beam along with the HP rating ( although that's not clear if it's for that particular hull or a larger one ) . Bottom and modifications have been discussed as well .
  2. M

    Listing to port side

    I would try sanding off the lip of the hook so it looks like a continuation of the hulls bottom . Then after putting a tab on the port side , the wider the better , take it out and see how she rides . If still listing a bit , remove the rest of that section. Leaving it on will ,in a small way...
  3. M

    Listing to port side

    The hull appears to be very narrow , which in itself will list quicker and more severely than a wider hull . The port side of the hull has next to nothing for a planning surface compared to the starboard side . It will allow that side to dig in especially with the larger planning surface on the...
  4. M

    Gph at various rpm...thoughts?

    Pretty sure you have that backwards . Your 115 is more like a 100hp figuring a 10% loss of hp between the crank and the prop . Try Googling it .
  5. M

    Stringer question

    Could be . If it was my hull and someone inspected it while second guessing his equipment , I would want a 100% , the stringers are shot from him . Me , I would then look for any clamps ,brackets etc . screwed into the stringers in the bad reading section . If nothing was in the " questionable...
  6. M

    Conversion from I/O to outboard on Islander.

    When the OP wrote Islander my first thought was a Starcraft Islander , not the glass , Grady White ? . So knee braces ,as noted above , are not used .
  7. M

    Conversion from I/O to outboard on Islander.

    My thoughts are , replace the wood in the transom, put knee braces in , 45* angle from new wood to stringers . I would find a similar hull with outboard hanging on it and look at the inside transom setup , including width of transom in case they use less width on the I/O setup .
  8. M

    Don't know what I got

    Yachtsurvey.com
  9. M

    Need Help & Advice on a Purchase....

    Uhhhh , inboards come with mufflers , inline or cans , my 305s are inline and the 454s are the larger cans . They can " discharge " out the stern , sides or at a 45* angle where the transom and side meet . Bigger engines have bigger exhaust ,they have to breathe , in and out and that usually...
  10. M

    Need Help & Advice on a Purchase....

    Pretty wild statement. When was a 19' boat brought into this thread ? Might as well said 15 ' . " Big engines are quieter & save gasoline at normal cruise speeds . No they are not quieter , my 454s have a 5 " exhaust outlet , my 305s have a 3" outlet , 454s are louder . Science speaking here...
  11. M

    Need Help & Advice on a Purchase....

    2nd the Four Winn , outdrive in fresh water all its life is the way go . Closed cooling system in each setup I take it ?
  12. M

    Head tank removal

    By law ,the macerator pump should not be hooked up while on inland waters . There should be a through hull valve that has a hose on it that goes to the pump. That hose should be removed or at the very least the valve is shut off with a removable handle. That handle probably should not be stored...
  13. M

    Head tank removal

    Does the holding tank have a macerator pump that would include a check valve for discharging when you're X amount of miles from shore ( Ocean only ) . That's where I would start when looking for a possible water leak . You have two hoses going to the tank , one from the head and one that goes to...
  14. M

    Stringer question

    You've been doing this for the last decade and have not pulled any bolts or screws that are in the stringers or drilled any holes in the wet areas to see if you have dry shavings ? Moisture meters are not always accurate, depending on when the hull was pulled , even bottom paint will affect the...
  15. M

    2007 Smokercraft 1660 / Sportsman

    Pictures would help ,things like knee braces , already wood there and holes cut out for drive might get you help from all the marine engineers on here 😅.
  16. M

    Advice needed on 12'-14' jon boat purchase.

    Lund has the best reputation, probably cost more as well . The upside is the resale value is much higher than the other two brands and will be easier to sell when it comes to that . That hull would be my first choice , would not buy either the Lowe or Tracker , have not read anything good about...
  17. M

    Performance expectations for a smaller boat??

    Why don't you take it for a sea trial, that'll tell you all you need to know.
  18. M

    Performance expectations for a smaller boat??

    You mentioned everything but your actual HP .
  19. M

    Performance expectations for a smaller boat??

    60 hp 4 stroke Mercury on a 16'7" Lund XL Rebel ,side console ,not a tiller , hits a bit over 30 GPS with 2 people, full gear ,trolling motor ,two batteries and gas . .
  20. M

    What year is this campion explorer 492

    Boat , trailer and motor are usually sold as a package so the odds are they are all the same year , meaning the boat is more than likely a 06 , as the seller stated .
Top