Search results

  1. alldodge

    IAC Valve Silencer hose

    Welcome Not a Suz expert but the hose is routed away so you won't hear the air suction. When motor is idling air is drawn in thru the open hose to the IAC silencer. From silencer to the IAC and then into the intake. The silencer is like a foam air filter, it lessons the sound of sucking air...
  2. alldodge

    repowering 2006 Chaparral volvo 5.7 with stroker.

    Just noticed this is a VP. At marineengines site I was thinking it was a Merc. Same things go with the ECM reflash but even more so with VP, probably won't be able to. Hey @Scott Danforth your thoughts You won't need to go thru hull unless you just want to, or might be if go radical with the...
  3. alldodge

    Mercruiser 4.3L won't start

    Missing spark
  4. alldodge

    Mercruiser 4.3L won't start

    If your getting spark to all plugs then it should fire Pull plug 1 and put your thumb or finger over the plug hole. Bump the starter until your thumb gets pushed out (this is TDC number one). Check position of the rotor to see if its point at or close to number one. If not real close move the...
  5. alldodge

    Mercruiser 4.3L won't start

    If timing was off and you have gas then there should be some kind of backfire How old is the gas
  6. alldodge

    Mercruiser 4.3L won't start

    Scratch that, might just be correct
  7. alldodge

    Mercruiser 4.3L won't start

    Run thru the guide
  8. alldodge

    Mercruiser 4.3L won't start

    Appreciate getting the pic, but that's a casting number. The motor serial number will be on a aluminum tag above the starter riveted to the block
  9. alldodge

    Mercruiser 4.3L won't start

    Not able to find that serial number, thinking it's maybe a 1985 model or there about, MCM 205, points distributor If the boat has a Tach, remove the wire from it. Could be the negative side of the coil might have 2 gray wires (one for Tach and one for distributor)
  10. alldodge

    Mercruiser 4.3L won't start

    The distributor doesn't look factory, what brand is it? What is the motor serial number? Does the finger mean the rotor? Explain can't attach distributor? No, not normal See if you have 12V on the purple wire with the key ON
  11. alldodge

    60 HP Mercury 4 stroke cuts off when warms up.

    Thanks Looks like your motor uses a vapor separation tank VST Not real familiar with your motor but find the VST and look for a schrader valve (bicycle tire fitting) which will have a plastic cap on it. Find/rent a fuel pressure gauge and attach to it. Then run the motor and watch the pressure...
  12. alldodge

    Fuel Tank size for 2001 Ventura 221

    It should work now, try it again
  13. alldodge

    Fuel Tank size for 2001 Ventura 221

    Welcome Spec shows 40 Gal Boat link
  14. alldodge

    Planning out installing NMEA 2k

    Active trim works great if programed correctly. I see the down side as the trim pumps run a bunch so may burn out sooner
  15. alldodge

    2010 etec 150hp solenoid?

    Maybe weak battery or corrosion on cables Place voltmeter on stater and see what the voltage is when turning key
  16. alldodge

    2001 1900sr maxum

    Push throttle only button in and move handle forward. The center button should be able to be removed now by popping it out. Once button is removed can get at the fastener inside
  17. alldodge

    60 HP Mercury 4 stroke cuts off when warms up.

    Welcome Have a serial number?
  18. alldodge

    2006 Monterey Boat with a 4.3L Mercruiser TKS Engine S/N 0w354897 Mysterious Loss of Power

    I said Temp switch is connected directly to ignition power and if it starts shorting out it normally blows the fuse. If it just draws enough power to low the 12V supply below 10V and not blow the fuse this can cause spark issues Again need to test
  19. alldodge

    Removing transom bolts Gen 2

    When installed correctly it will not lea and holds. There are 2 sizes of bolts (Items 2 and 3) and are locktited in place. Will need some heat most likely to break them free easier
  20. alldodge

    GX1850

    Don't know if GX1850 is certified or not. Quick search doesn't mention certified, but is not do hot swap. If I think about it next time at the boat I'll turn one of the displays off and back on to see if it reconnects The displays use CAN with 2K connections. If 2K has a direct connect to the...
View older results
Top