Search results

  1. T

    No core floor

    Are you only concerned about the thickness of the portion of the floor that runs under the open bow floor? If so, use a router, belt sander, hand planer, or something similar to thin out a piece of 1/2" plywood in the 6-8" where it will tuck under the open bow floor. Use a smear of PB to make...
  2. T

    1979 Glastron Carlson CV-23 restoration

    Oof, time to bite the bullet and do a full gut of the wood structure instead of trying to apply band-aids.
  3. T

    1977 Crestliner Muskie 7**, Outboat Restore Project

    I didn't want to put holes in my beautiful sealed deck either, so what I did was make some "pads" out of solid mahogany and PB'd those in place, tabbed them in with 1708, then covered in 1 layer of 1.5 oz CSM, and finally gelcoat. Mahogany is a rot-resistant wood and can take a screw very well...
  4. T

    1990 Bayliner 2651 resto

    Agree - cut the fiberglass out of the keyhole. Install the new transom wood, glass it in place, then you can glass the inside of the keyhole.
  5. T

    Rotten 1982 Beachcraft

    There is definitely a learning curve to using contact cement, but once you understand it, it's great stuff.
  6. T

    1981 Citation Marquis restoration...

    The "pin" in a blind aluminum rivet is the steel core used to mushroom out the back side of the rivet when you pull it to set it. The reason the drill bit walks off is because it's a steel pin inside of a soft aluminum rivet. Usually I take a small drift punch and a hammer and knock the pins...
  7. T

    Advice on transom , stringers and floor rebuild

    I went with 3/4" plywood for my sun-pad too.
  8. T

    Transom Repair 1984 Bomber Scout

    If you love this boat enough to put a few (several?) thousand dollars and a few hundred hours into the repair of, pull the rub rail, pop the cap, take dimensions, demo, and rebuild. Otherwise, it may be a better option to spend your efforts and money on a boat in better shape.
  9. T

    1981 Citation Marquis restoration...

    I wouldn't sweat it, since it'll be covered by the rub rail. Brace yourself for further disappointment with OEM boat manufacturing practices as you continue to dig in.
  10. T

    Trim up not working.

    Trailer switch raises the drive with no limit on where it will stop until its all the way up. Trim up button raises the drive but stops when the trim limit switch is tripped, so you don't trim up too far with the engine running. Sounds like your trim limit switch may be out of adjustment or the...
  11. T

    1981 Citation Marquis restoration...

    When I de-capped mine, it seemed like the hull bowed outward coming from near where the floor attaches (at the chines). I did not build a cradle or do internal bracing - just crossed my fingers and restored the hull on my bunk trailer. I did take width measurements every foot immediately after...
  12. T

    Carburetor Issues, Dripping Carbs...

    That's crappy. What brand / supplier did that float come from so we know to stay away?
  13. T

    Rotten 1982 Beachcraft

    Thanks! Yes it was a labor of love, and it was all worth it in the end. Your project is looking great, keep up the good work.
  14. T

    Keel damaged

    Grind/sand and fill with your gelcoat paste, or make your own next time by adding some cabosil to regular gelcoat. Wet sand and buff to fair it in to the surrounding areas.
  15. T

    Suggestions for fiberglass repair along the keel

    Grind it out to fair it to the surrounding surfaces, tape it off, and apply some white gelcoat thickened with cabosil. Wet sand and buff to taste. Unless you're a stickler, no need to try to color match since it's on the bottom of the hull and nobody is likely to ever see it.
  16. T

    Polyester resin cracked while curing

    Glass over it and you'll be fine. Too hot of a mixture or too big of a glob of PB to cure at once will cause that.
  17. T

    Rotten 1982 Beachcraft

    Looks good. Biscuit cutter's a handy tool that I've never had the pleasure of owning. I did scarf joints to stretch my 8 ft plywood to 12 ft to make stringers.
  18. T

    Noise from engine compartment when steering left or right

    If the noise is constant while holding a turn and you don't have power steering, it's probably gimbal or u-joints. Buy an alignment tool, pull the drive, and inspect the gimbal bearing alignment and inspect the u-joints. Does the noise change based on how you have the drive trimmed? Even...
  19. T

    2002 Mastercraft 5.7 harmonic balancer moving in and out

    I'd be buying a Scat 383 rotating assembly and taking the block to a competent machine shop, letting them know the situation so they can inspect for any damage.
  20. T

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Another great weekend at my brother's lake house is in the books. I spent nearly the entire month of July in SoCal for work so coming back to The South's humidity, rain, and heat was a rude awakening, but it sure was nice to be back behind the wheel of the Power Play. The boat ran out great...
Top