Search results

  1. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I am up early this AM. I think this is the page you are referring to . . . . .
  2. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    BTW - for those who have not used oxalic acid, here is what 'AI' says about it. . . "Soaking an iron casting in an oxalic acid solution is a common method for removing rust. Oxalic acid effectively removes rust (iron oxide) by converting it into water-soluble iron oxalate, which can then be...
  3. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    BTW - The more I think about the exhaust pieces, it looks like the best thing is to unbolt the riser from the exhaust manifold, swing it up 90-180˚ and pull it out of the rubber coupler (boot). Then the other pieces should come apart as needed.
  4. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I filled the risers with a fairly strong mixture of oxalic acid (via a long hose to the lower fitting) and will let it sit overnight. I have an appointment in the AM, so I'll be out on the boat in the PM running some neutralizer and seeing how things look.
  5. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Not much luck getting the exhaust pieces separated. The boots are plenty loose, the pieces just don't want to go. I'm done fiddling with them, I'm on to an acid soak of the internals, to the greatest extent that I can. I'm using oxalic acid (aka wood bleach). I've had good luck before...
  6. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I'm trying to get the boots off the exhaust risers and elbows so I can get a look at the riser internals. . . They are no easier than the old style to get apart. So far, I have taken off the clamps and briefly ran the engines to loosen the boots up (which they did). Still hard to get things...
  7. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    @Scott Danforth . . . 5th strainer . . . Before all the other strainers . . . . :LOL:
  8. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Yes, the highest that I have seen is 80˚F for water temp and it only lasts for a couple of weeks. I'm also thinking flow issue, so I'll see what I can do short-term, as I only have a couple of days to work on it. I think I need to run the Diacom recording for longer - yesterday it was only...
  9. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Hi @Lou C - The exhaust is steel, both manifold and risers. AFAIK - The exhaust has never been inspected or replaced. The boat is in its 10th season, so not a surprise that it needs some love. ;) Out in the bay, I was getting a water temp of 78˚F . . . in the harbor it was a little less. We...
  10. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Hi @Lou C - The exhaust is steel, both manifold and risers. AFAIK - The exhaust has never been inspected or replaced. The boat is in its 10th season, so not a surprise that it needs some love. ;) Out in the bay, I was getting a water temp of 78˚F . . . in the harbor it was a little less. We...
  11. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Here are a few more graphs . . . Clearly the starboard engine shows the riser temp coming down and then going up whereas the port just climbs . . . Water pressure and ECT look OK. File names denote the engine(Port/Stbd) If it is nice and sunny tomorrow, I'll clean out the Port and starboard...
  12. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    water was 76-78˚F
  13. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Update for today . . . I checked the following . . . Port engine: Coolant in H.E. = full (both engines were & are full) Poppet valve: I removed the cover of the valve assembly . . . no build-up or anything and the spring action of the valve seemed normal . . . I could open the valve with a...
  14. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Also, I've been wondering what these things attached to the fittings were . . . . Apparently a check valve (8M0103408) . . . I guess it is to allow the raw water hose(s) to drain while the engine is not running?
  15. tpenfield

    454 mag mpi chuggles/stalls

    Thanks . . . thinking it may be helpful. Do you have the recording file from before? Could just use that to make the TPS graph.
  16. tpenfield

    454 mag mpi chuggles/stalls

    Got a graph with the TPS reading during this recording?
  17. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I've grabbed a few images from the Internet that show the parts under discussion. . . Above is the rear view of the engine, showing the P/S cooler and poppet valve. It looks like water to the risers branches off at the back of the engine via the 'Y' pipe (#12 - 8M2003728). So, the 'strainer'...
  18. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Are you pulling an all-nighter? My California peeps will be here next week, so hoping to have the boat operational for their visit. And yes, the port side of the port engine is nearly impossible to get to. I might practice on the port side of the starboard engine first, as that is an easier...
  19. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I think I found in this picture where the 'strainer' is located. . . I'll take a look and see if that is clogged, etc. If not, then I'll take a look at the poppet valve.
  20. tpenfield

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    Thank you for the reply . . . I will look into the 'strainer assembly', as that may have some residual blockages from the 5 years of operation prior to my putting sea water strainers in before the sea water pumps.
Top