Search results

  1. J

    No telltale Nissan 90hp

    Are all of the water pipe seals where the pipe slides into the water pump housing in good shape and installed properly? Did you replace just the impeller or do a kit? It can be a problem if the cup or plate are grooved.
  2. J

    Raising outboard higher

    Good to see you got it fixed. Before outboard jet drives were really available from the motor manufacturers, I worked for a boat dealer in Alaska who was selling jon boats with aftermarket outboard jet drives. He was having transom risers made to get the jet up where it belonged. Basically...
  3. J

    Suzuki DF175 surging at high power setting

    The guy needed the trailer for a different boat so he took it back to the lake before I had a chance to fiddle with it again. He sent me a video showing the boat was running fine. I did notice the tach reading a good bit past 7,000 rpm even though the engine sounded normal. SDS arrived today...
  4. J

    Suzuki DF175 surging at high power setting

    Replaced the high pressure filter and ran on the lake today. No change. I guess it could be going into a guardian mode but not getting any alarms or lights.
  5. J

    Tilt / Trim Motor Torque Specs

    I spent 20 years wrenching on military aircraft. Used a torque wrench on nearly everything and was taught the wrong terminology. Very hard habit to break but every bit as bad has confusing “then” with “than” or “break” with “brake” or “their” with “there”. At least the last 2 examples rhyme...
  6. J

    Creaking/popping power trim

    One of the boats I look after has a zerk on the starboard end of the pivot tube but not on the port end. Another one doesn’t have any. Most have one on each end. I have a few motors in the fleet that creak and pop trimmed or tilted up. They have been that way since before I joined the...
  7. J

    Suzuki DF175 surging at high power setting

    Just started getting a 1000 rpm surge at high power settings going across the lake. Not feeling a miss. I think about 1100 hours on the motor. - Replaced the low pressure filter. No change. Tank run with no load shows: - High pressure side reads 70 psi when the key is turned on and 40 psi...
  8. J

    1997 Honda BF40A trim fluid check?

    The circled bolt should be the fill level check.
  9. J

    BF200 power loss at full throttle

    I didn’t hear anything for 2 weeks but today they said it is acting up again. It only seems to happen when the boat is pushed hard. The day it acted up on me I ran it trimmed up at full throttle for over 2 miles before it missed a beat. I had my wife drive while I crouched next to the motor but...
  10. J

    BF200 power loss at full throttle

    They finally got the boat off the lake. I spent all morning trying to figure out how to make a connection with my fuel injection service kit only to find out it isn’t an easy task unless you buy the Honda tool. It threads into a standard 6mm(?) hole and I have nothing that can do it. I...
  11. J

    Honda BF60 Dies Above 3kish RPM

    HEADS UP!!!! I just learned the Harbor Freight fuel injection service kit does not have the connector needed to connect to a new BF200D I need to check. I do not know about your 60hp but this is the first time I didn’t have an easy connection. Might just be a Honda thing.
  12. J

    Honda BF60 Dies Above 3kish RPM

    I can’t think of anything you haven’t covered without going into the electronics of the motor. Maybe it is losing the signal to the injectors for some reason. Throttle position sensor?
  13. J

    Honda BF60 Dies Above 3kish RPM

    Not so on all fuel injection systems. I was able to install a portable tank with a primer bulb on a Mercruiser equipped boat that had a failing injection pump to make it run good enough to drive the across the lake and load it on a trailer. The boat would run good for about 2 minutes after...
  14. J

    Honda BF60 Dies Above 3kish RPM

    I bought a harbor freight fuel injection test kit a few years ago. It is essentially a pressure gauge with adapters for nearly everything and has served me pretty well working 6 or 7 different brands of marine motors for no more than it cost. It does sound like low pressure is a long shot...
  15. J

    BF200 power loss at full throttle

    Good ideas on both but any restriction upstream of the primer bulb would cause it to collapse. The boat had an aftermarket flowmeter installed this spring. I might try bypassing that. The boat was rigged with 5/16” fuel hose. That seems small for 200 HP. All of the 150 HP Mercurys and...
  16. J

    BF200 power loss at full throttle

    New motor last year. 121 hours. Typical clogged fuel filter symptoms except both have been changed. Runs great for about 2 miles at full throttle then falls on it’s face. Let it idle for a bit then go again for a shorter distance. Primer bulb doesn’t collapse. Pumping primer bulb when engine...
  17. J

    pdf service manuals

    I keep my pdf files on my phone or tablet so no need to print and carry pages to the shop. Most of my manuals are paper and live in the shop but I have some Mercury, Yamaha and Volvo on my phone.
  18. J

    Water in the fuel

    The same thing as the cap on a lawnmower. The vent is covered by the outer cap.
  19. J

    Water in the fuel

    Condensation in a boat fuel tank isn’t any different than condensation in any other fuel tank or can. The easiest way to prevent condensation is to minimize the amount of air in the tank. I know one of the outboards (2018 Monterey) has a vented cap. It’s all I could find to fit the threads in...
  20. J

    Water in the fuel

    Fuel supply okay. 16 boats running on the same supply. I would be seeing more problems across the fleet if not. Not sure on gas cap but I think it’s original to the boat (2017).
Top