Search results

  1. Scott06

    What prop? I'm lost

    Given you don’t have a prop I assume you just bought the boat? Personally Try a 19” 3 blade aluminum to rough in where your wot rpms will land. You can move up to stainless from there and tweak pitch You may be aware that Yamaha only sold sterndrives for a handful of years , parts are hard...
  2. Scott06

    93 mercruiser 4.3 alpha one gen 2 fuel problem (I think)

    yes the fuel pump or off purple wire will provide a igntion on 12 v source
  3. Scott06

    Help me set up my new edelbrock 1409

    Bottom right of the first and top left of second of the page have how you should do it. This is out of the merc 3.0 manual.
  4. Scott06

    Can I lubricate the cutlass bearing with something so I quickly test forward and reverse on the trailer

    Water is what lubes it in use
  5. Scott06

    Help me set up my new edelbrock 1409

    It’s under load idle will drop from where it is in neutral
  6. Scott06

    No start after engine install. Need Help!!!

    Good point . I have. 2 grey wires on mine one to coil one to tach. If no wire is on net post of coil It will not fire. can disconnect the tach wire on back of tach Or check for continuity to ground with a volt meter
  7. Scott06

    No start after engine install. Need Help!!!

    Go through the rest of the TB troubleshooting guide.
  8. Scott06

    No start after engine install. Need Help!!!

    The TB troubleshooting guide starts with verifying the tach wire isn’t shorted to ground …
  9. Scott06

    Hole shot

    So I….
  10. Scott06

    No start after engine install. Need Help!!!

    Disconnect the tach wire (grey) at negative post on the coil. This will remove any chance the tach is killing the spark you can also disconnect it and check for continuity to ground with a volt meter. woukd agree battery and connections both positive and negative are suspect given the voltage drop
  11. Scott06

    Engine hour meter clicks with ignition on, but engine not running

    On an analog engine that is the only way to know it is running ( or should be…) power to ignition circuit.
  12. Scott06

    No start after engine install. Need Help!!!

    the oil pressure alarm doesn’t interrupt the ignition. It just makes the buzzer go off when below 4 or 7 psi.
  13. Scott06

    No start after engine install. Need Help!!!

    Wi willing to bet during cranking you are loosing voltage, start with positive battery and ground cables.ther are 2-3 at the back on flywheel cover Measure with a volt meter on positive terminal of coil while cranking should stay close to 12. Then go through the thunderbolt ignition...
  14. Scott06

    outdrive stuck

    That’s the point with a press you wont damage the splines unless you are chit faced…a bar on either side of the bearing or use bearing separator , press down on the center of the shaft with a pice of round stock or socket
  15. Scott06

    outdrive stuck

    Yeah I put mine on wheels but fervently stub my toes on it. I bought mine for rebuilding the suspension and changing rear gears on my gto. Was right there when rebuilding jet pump on the seadoo and doing seals and bearings on my outdrive. For all the work you do it’s worth it.
  16. Scott06

    outdrive stuck

    If you were changing the u joints yes take the yoke off put it in a $100 harbor freight press and it will come off with out damaging anything The press is well worth the investment
  17. Scott06

    Intermediate shift shaft play?

    It isn’t the tightest fit when new but based on your comments replace the bushing and seal likely is needed based on your comments
  18. Scott06

    Learning to wake board at 48. What am I doing wrong?

    I also learned to wakeboard in my mid 40 s Could be a couple things would try switching which foot is forward as suggested Also I have found leaving the board at a 45 degree angle ( for me to the left) vs perpendicular makes it easier to get up. This may not be correct but then as I get up...
  19. Scott06

    outdrive stuck

    Yes you can cut it off just take care on the inner race not to cut into drive shaft
  20. Scott06

    2024 wake pro 230

    would Really defeat one of the prime benefits of having a closed cooling system if you had to change out the AF
Top