Search results

  1. Tafflad

    Removing impeller

    Needs must. :-)
  2. Tafflad

    Hull support trestle

    Years ago I rolled trailer off the back onto a stack of large 4x4 tyres ... but this is a heavier boat.
  3. Tafflad

    Hull support trestle

    Picture of boat as requested .. overall 21' ..... hull length 19' I want to jack rear up onto stands then get trailer out from underneath ... appreciate a bit of shuffling will be needed due to trailer axles.
  4. Tafflad

    Removing impeller

    Guys - success ..... obtained a 3/4-16 UNF machine screw, this screws into the end of the impeller, and on tightening brought impeller out about 1/2" Then by levering with a small pry bar between spanner & housing the impeller came out. I will put a threaded M10 hole through the center of the...
  5. Tafflad

    Removing impeller

    It's possible ..... but I would need to know which puller has a thread of 3/4-16 I did try those part numbers on-line and nothing shows. It's a chicken & egg situation for me ..... once I have impeller off I can measure etc on the bench - until then not so easy. Annoying Volvo do not produce a...
  6. Tafflad

    Removing impeller

    I thought it was more confusion - there is a Sherwood 25105 and also a Sherwood 25106 the latter aligns with the video M16 Fine comment On checking the 25105 is as you state above 3/4"-16 UNF and that would have for a female thread a minor diameter of 0.6823" .... which is equal to 17.33...
  7. Tafflad

    Removing impeller

    Don't apologise ...... FYI just had parts supplier get the tool of shelf and try it in the impeller - and it was too small (far to loose) The 3/4"-16 thread is interesting all the other parts related to pump have been Metric. Guess I need to find a 3/4"-16 UNF machine screw. The Sherwood tool...
  8. Tafflad

    Removing impeller

    Do you by any chance know what thread is on the 'screw-in bolt' ? ... if I know what the thread is I could make the tool easy enough. The second of the 2 videos mentions an M16 Fine bolt, but not sure if this is for this impeller.
  9. Tafflad

    Removing impeller

    I'll ask them now
  10. Tafflad

    Removing impeller

    It would be too difficult to remove pump at full arm stretch .... fingertips can only just reach the pump.
  11. Tafflad

    Removing impeller

    I just spent another Hr with no luck. Managed to borrow a pair of parallel jaw pliers ... now then have immense grip. Still could not budge .... probably as I'm at arm's length so I am in effect trying to push pliers at full stretch, and not getting enough force. Unless I can make or...
  12. Tafflad

    Removing impeller

    Interesting - I lodged a request with Volvo spares ... their response is : "The impeller kit is VOP21700445 Although this impeller does have a threaded hub, there is no puller kit listed for it at the moment. I have checked the 3 different versions Volvo Penta sell, but none of them are the...
  13. Tafflad

    Removing impeller

    Thanks for the comments .... I have never removed impeller for winterising before, it was the dealer who said it should be removed to prevent a permanent set in the rubber vanes. So ‘3843948’ would be the correct part for the puller for my impeller ‘21700443’. ...... I agree if I were buying...
  14. Tafflad

    Removing impeller

    If Inread it right .... it’s 21700443 tge issue is when I Dona search on that on .. the items shown do not have a female thread .... just looked at 5 search results ... they all look like this ..->
  15. Tafflad

    Removing impeller

    When I googled couple of responses say it’s for D3 engines ... do VP use common impeller ? I tried several Volvo Spares sites ... my engine is V6-280-C-N none of the sites list this, they do list V6-280-N and V6-280-CE-N On both of those they list Impeller kit as 21700445 when I look at...
  16. Tafflad

    Removing impeller

    Been doing some Googling ... found details of 2 types of impeller puller. . . This 2nd video mentions that you can use an M16 fine threaded screw. (3:42) . . . . Anyone know if M16 fine is correct for VP, he mentions Sherwood, I’m not familiar with that make.
  17. Tafflad

    Removing impeller

    Not sure it would be imperial size ... so far all screw & bolts have been metric on this. 15mm Sepentine tensioner, 9mm screws holding on pump cover. is this motor all metric ? Or a mix
  18. Tafflad

    Removing impeller

    Wishing now I had not started .... never removed on any other motors.
  19. Tafflad

    Removing impeller

    I’ll have to remove bench seat and rear panels to allow to get in-line with it and try again.. certainly could not remove it working at arms length.
  20. Tafflad

    Removing impeller

    Never owned a VP before .... have 2020. V6-280-C-N after discussions in separate post, only remaining winterising task is to remove impeller. I removed front plate, but cannot get impeller out. I have tried for over an hour with various needle nose pliers, and it does not budge. Am I correct...
Top