Search results

  1. Lou C

    repowering 2006 Chaparral volvo 5.7 with stroker.

    No in salt that won’t destroy the motor unless you neglected the manifolds/elbows. We routinely get 1500 hrs or more here in the salt
  2. Lou C

    The End

    I haven't used our snow blower in 3-4 years. This is why I started draining the tank and carb bowl, and I do that on all my power equipment that has a bowl type carb. Less problems that way.
  3. Lou C

    The End

    My F/W is winterized, the outdrive is off and in the garage, but I still have my 2 Walker bay dinghies on the beach (they stay there all the time) and my little Suzuki DF2.5 is ready to go!
  4. Lou C

    5.7L Cam Choice

    1) the 1985 GM (Chevrolet) block is a 2 piece rear main seal, vs the 1986 and newer 1986 and up one piece main seal. When they went to the one piece the flywheel changed, and I don't think your coupler (Merc or Volvo) will work with the 2 piece style rear main flywheel. So you have to check on...
  5. Lou C

    A nice tip but it’s not about stern drive storage in the up position

    If it ain't broke....keep on rockin' it isn't that bad of a job as long as the end cap will come off, I used a bit of heat and constant pressure on the pin wrench.
  6. Lou C

    A nice tip but it’s not about stern drive storage in the up position

    The advice I have read said that if you leave it full up don’t leave it fully up against the upper limit because that can cause the check valves in the pump to stick.
  7. Lou C

    End of season maintenance checks…

    I used the one that you refill the drive from.
  8. Lou C

    Can I Tell if Water is Getting into the U-Joint Bellows?

    Unfortunately there’s no way to know if it’s going to leak. While it can be a pain that’s why pulling the drive at the end of each season helps to make everything last longer.
  9. Lou C

    A nice tip but it’s not about stern drive storage in the up position

    I just rebuilt my trim rams this spring, one started leaking a bit the year before, I was shocked how long they lasted. The BRP kits are about $50 for each cyl, if the end caps come out off easily you can leave the trim rams on the transom mount no need to disturb the hydraulic line fittings. If...
  10. Lou C

    End of season maintenance checks…

    Did a bit of maintenance checks, scoped inside of manifolds and did a pressure & vacuum test on the old Cobra drive. One manifold was totally clean the other did have some light rust probably from condensation because that side always runs a bit cooler. OD held pressure at 16 psi & vacuum at 13”...
  11. Lou C

    Did Water Get Into My Gear OIL?

    Should be dark bluish green. Not light which suggests water.
  12. Lou C

    Changing the U-Joint on an OMC Cobra Out Drive, OD

    If you get brown crud out of the ujoints that’s not normal and they’ve internally rusted and must be replaced. If they fail with the boat up on plane it could tear up the transom mount & let water in the boat. Risky & potentially dangerous. Speedy sleeve is a thin sleeve that gets installed over...
  13. Lou C

    Replacing transom foam seal

    Agreed if they’re good no reason to replace
  14. Lou C

    Trailer fit?

    The trailer fram does go to the back of the boat, if it has enough tongue weight you can shorten those bunks…
  15. Lou C

    Changing the U-Joint on an OMC Cobra Out Drive, OD

    What about the drive shaft & ujoints? Once you get it right it will be fine. I have had good luck with mine now used & moored in salt water 20+ years. Pulling the drive yearly, doing pressure & vacuum tests & changing & adjusting the shift cable when needed is what it takes to make it last….
  16. Lou C

    Replacing transom foam seal

    “Easy” and “trim hoses” doesn’t belong in the same sentence! Proper line wrenches and maybe judicious use of heat will likely be needed. If the rubber is cracked then yes have at it but if not, leave ‘em!
  17. Lou C

    Bottom paint around transom assembly

    If you want to paint that area just use the same safe for Alu paint you use on the outdrive…just use an alu safe paint stripper…be careful sanding any bottom paint they are all toxic to an extent!
  18. Lou C

    OMC COBRA 5.8 EFI and ESA

    Did TC rebuild the whole drive or just the lower or upper? I would contact them if it’s a recent rebuild. If you want to check it yourself here’s OMC’s specs: Pressure test, first 6 psi then 16-18 psi Vacuum test first 5”Hg then 15”Hg Yep there’s no way a high gear oil level causes shifting...
  19. Lou C

    Mercruiser 4.3L won't start

    That’s the part # of the intake manifold. Merc puts a plate above the starter
  20. Lou C

    Changing the U-Joint on an OMC Cobra Out Drive, OD

    Marine engine.com Been using them for years
Top