Search results

  1. Scott06

    She just won't start easy nor stay running 4.3l

    Oil pressure 50-55 is really good, usually a cold reading as oil thins when engine gets warm. good rule of thumb is when oil is warm to have 10 psi for every 1000 rpm of engine speed. I usually have about 55-60 at 4000-4500 when good and warm. more if the lake is still cold
  2. Scott06

    Mercruiser 3.0 TKS - Hard to start when semi-cold

    2002 would not have a TKS they came out later maybe 2008 give or take. My 2003 was a choked mercarb
  3. Scott06

    Time for my first bellow change, tips?

    Parts are on this breakdown drawing https://www.marineengine.com/parts/mercruiser-sterndrive-parts/alpha-one-genii-1998-and-up/0l100040-up/oil-reservoir-components Looks like there is an E clip on the inside of transom housing should pull through the stern . give the exhaust bellows a try I...
  4. Scott06

    Prop, or Engine Issue?

    You may be able to get your existing prop repitched by a prop shop. No diameter is not tied to lower unit design except for max diameter a drive or outboard can use. Normally when props go down in pitch diameter goes up some (not a 100% rule). So if you find a 15 " pitch prop that fits your...
  5. Scott06

    Time for my first bellow change, tips?

    It’s not for international parts but so they can sell parts outside of merc dealer network. For example you can buy quicksilver hi perf gear lube at Walmart In the US
  6. Scott06

    Help value a Smoker Craft I’m looking at

    the fact that the owner is not hesitant to lake test it means its been taken care of and maintained. due your homework check compression and leaks transom , but I don't think that's a bad price. You will be able tell when you get there if the guy takes care of stuff...
  7. Scott06

    Time for my first bellow change, tips?

    I did it with complete bellows job. on last two boats this was the only time I had to get in there. My last boat I think was on original shift cable. Sold it the year in my mind I was gonna do bellows... This boat made it 18 years before needing bellows (exhaust had split but shift and...
  8. Scott06

    Time for my first bellow change, tips?

    It does freely slide out of the transom. I think there may be a plastic clip in there. I think there was one in my transom kit that I didn't bother replacing cause its hard to get to. either way cable slides out when you pull the bellhousing off.
  9. Scott06

    mercruiser coolant lines

    its a low point and needs a drain for freeze protection
  10. Scott06

    3.7 gets hot while idling

    As mentioned by others this engine is very sensitive to slight over heats. Not sure if you have the upgraded heat exchanger or not? If it were my boat I would start with replacing the impeller including the base and housing as they are plastic. Check the water tube is not collapsed and you are...
  11. Scott06

    Alpha one gen 2- upper drive shaft seal leak

    You will need the wrench to take off the input yoke, use some heat patience and good penetrating oil like Kroil. the seal needs to come out from he outside in So you have to tear down the upper. Keep track of where any shims go and if you don’t replace bearings existing shims should be ok. get...
  12. Scott06

    This happened today, and in the blistering heat.

    Jetskiis too. On older Sea doos like mine they are plastic. A buddy mentioned his broke while towing. When he got where he was going ski was about a foot farther back
  13. Scott06

    EX Lube bearings on new to me trailer, how often to physically check bearings?

    I think what you outline makes sense and is what I would do. I think these are really nicely set up so you can pump out old water contaminated grease with fresh new grease. Would pump until fresh grease comes out. How much or how far do you tow?
  14. Scott06

    1999 Searay 185 Knocking

    2022 was a life time ago... Yes but now that you are having issues unscrew the fuel filter and dump contents into a clear container. You would be looking for water, phase separation and debris. What engine is in the boat? Obviously if you cant get on plane way down on power.
  15. Scott06

    1999 Searay 185 Knocking

    start with contents of fuel filter, suspect fuel contamination. also would start with compression test. What is maintenance history of boat and what do spark plugs look like
  16. Scott06

    Prop, or Engine Issue?

    yes prop is likely contributing but you are also correct to ask about condition of the engine. If you have good compression carbs and spark is in good shape then yes going down 2" in pitch should get you around 5200. For your set up assuming your speed is relatively accurate I would say your...
  17. Scott06

    Aftermarket stainless upper gimbal pin?

    Hills is usually pretty well regarded
  18. Scott06

    Time for my first bellow change, tips?

    And I was using a cheap poorly made bellows expander too. All in all wasn.t that bad, especially considering the originals were 18 years old. I doubt I will still have this boat in 18 more years
  19. Scott06

    Time for my first bellow change, tips?

    I had expected a fight when I did my exhaust bellows too but I didn't think it was a big deal, was glad I did full bellows vs the tube. Mine is a gen 2 to be honest I had more of an issue getting the driveshaft bellows retaining ring on
  20. Scott06

    Aftermarket stainless upper gimbal pin?

    Yes I thought you were OP...
Top