Search results

  1. tg3690

    Chrysler Break in Procedure

    If you click on the Technical Help tab there is a lot of good information there...FYI.
  2. tg3690

    Chrysler Break in Procedure

    You could do it all in one day if you wanted to but 10 hours of actual running is a long time.....probably more realistic to do several hours at a time. Have never seen anything that says it has to be done in a certain time frame....so if you want to run it at high idle/neutral for 20 mins then...
  3. tg3690

    Chrysler Break in Procedure

    https://maxrules.com/fixbreakin.html My factory manual shows a PH break in procedure, but I used this one from MasterTech Marine.....is basically the same but has a lot more detail and additional info.
  4. tg3690

    1984 force 125 Leaking tilt and trim?

    Was thinking that Chinese VB you got on ebay was suspect, now you have the motor apart...don't have much experience with that part of the system. If all else fails, Mastertech Marine has new API replacement units with complete motor and valve body assembly. Not cheap, but available...FYI
  5. tg3690

    1984 force 125 Leaking tilt and trim?

    What hole are you talkin about and how did you fix it?
  6. tg3690

    Guessing young adult kids text back rather than call?

    My kids.....I call them and no answer.....I text them they reply right away. It seems that "talking" is not cool anymore....lol.
  7. tg3690

    Do all forces have overheat buzzers?

    Had an extra horn laying around, got the LED light at local parts store.....bought a temp gauge/sender from Faria Beede, but there are others available.....maybe should have went with a water pressure gauge instead.....
  8. tg3690

    Do all forces have overheat buzzers?

    Same here....plus a louder horn and temp gauge.....
  9. tg3690

    The fall

    As the late Merle Haggard put it...."Like a snowball headed for hell" :ROFLMAO:
  10. tg3690

    The fall

    Hey jerry......check this out....lol. But seriously, hope you are getting better.
  11. tg3690

    How to set up an induction tachometer

    It wasn't long enough to reach my dash......way too short. Might be able to splice in some wire to make it longer but didn't want to do that.
  12. tg3690

    1984 force 125 Leaking tilt and trim?

    Are you filling the reservoir when the engine is fully down? You might recheck your hydraulic lines and make sure they are in the right holes on the valve body.....is not hard to get them in the wrong one......in this diagram the green arrow should go to the fourth hole, not the third one as...
  13. tg3690

    Do all forces have overheat buzzers?

    That explains why you probably don't have one......I would get one after you finish the other work you are doing......you might consider using a louder horn instead of the buzzer....need to be sure and hear it if it goes off.
  14. tg3690

    Big water leak inside cowl, any tips for this coming repair?

    I just noticed that Nordin said not to remove the spacer plate in post#4....not sure how you can replace that exhaust gasket without taking it off? Maybe he will chime in later and explain.....I would just get all three to be sure.....
  15. tg3690

    Big water leak inside cowl, any tips for this coming repair?

    Yeah....after looking at the diagrams again, that middle one looks like it goes between spacer and PH.....that one on the right not sure about.....all the listings I found for the exhaust gasket come with all 3.
  16. tg3690

    How to set up an induction tachometer

    This is the one I bought....that silver C connector is for the ground.....
  17. tg3690

    Do all forces have overheat buzzers?

    Was referring to the thing the steering wheel and gauges are mounted in....like a dash board.
  18. tg3690

    How to set up an induction tachometer

    The one I bought off ebay said at least 5 wraps....and connect the ground wire to a good ground.
  19. tg3690

    How to set up an induction tachometer

    I just got one to check my main tach.....I have a 3 cylinder so I set it at 3 spark per rev setting.....seems to work well. Try setting it at 2 spark per rev for your 2 cylinder and see it that works better......
  20. tg3690

    Do all forces have overheat buzzers?

    Both Crowley and marineengine.com show a buzzer listed......should have one unless a PO removed it for some reason.....look under and around the console....also should have a thermo switch that activates the buzzer. If you ground that switch it should set off the buzzer.....
Top