Search results

  1. jerryjerry05

    120 force bayliner Capri

    EBAY is the place I look for service manuals, stay away from Clymer and Seloc manuals.(unless they're free) Little more info? once it starts, when you lower it does it stall, how fast?
  2. jerryjerry05

    Gas spewing from Carb

    Clean the carb and while it's off, inspect the reeds???
  3. jerryjerry05

    85hp Force Under powered

    What's the compression readings? When you cleaned the carbs, did you make sure the jets were clear and no build up in them? Where are the air/fuel needles set? should be at 1 turn out, maybe 1 1/8? If they don't make any difference then the port cover gaskets might be sucking air? Do the...
  4. jerryjerry05

    New Force Owner, No Start Issue

    The backfire could be the gaskets on the port covers have gone bad and the motors sucking air. Do the starter fluid test: start motor, spray SF around the intake side of the motor. Any change in the way it runs means it's sucking air. ONE!!! backfire can blow the port cover gasket/gaskets. The...
  5. jerryjerry05

    Gas spewing from Carb

    Clean the carb.
  6. jerryjerry05

    97 force murcury

    Now I see the info. You should have added this to your original post. No they won't swap.
  7. jerryjerry05

    Will 02 75 2stroke lu fit my 97, 75 2stroke

    02 ?? Force didn't make anything after 99. More info/ pics will help?
  8. jerryjerry05

    No Spark After a Short - '89 50hp

    outboardignitiondotcom has test procedures for your motor. OEM or CDI ?? you'll need to pull the flywheel, CDI will have it's name on the part.
  9. jerryjerry05

    Throttle cable maintenance and adjust basics? Force 85 H.P. or other..

    Usually adjustments aren't needed unless someone tinkers or "adjusts" something. The cables: unless the ends are exposed to the weather then they don't need lube. The ends or connectors,, you can lube with a couple drops of oil. Silicone sprays end up getting sticky and can clog. If you lube...
  10. jerryjerry05

    Converting 99 40 hp Tracker/Force to Tiller Steer

    Pretty sure they didn't made a tiller model in the 40hp.
  11. jerryjerry05

    New Force Owner, No Start Issue

    Backfire/smoke: Could be the system is flooded or there's an air leak somewhere? Changed floats?? what floats did you change to? Most aftermarket floats won't work and cause flooding. Load test the battery. Rebuild the starter, the brush kits are cheap, they sell them here.
  12. jerryjerry05

    1986 Force 125 hp popping

    You said (the motor sound good for a few seconds and then abruptly stops. It also pops when trying to start.) This sounds like there's an air leak somewhere? The popping could be the air screws are set wrong or the port cover gaskets are bad and sucking air? Remove the carbs and check the reeds?
  13. jerryjerry05

    '95 120hp compression test results

    When did they go with stainless bolts? I've not seen them? If it started at all I'd say the gasket should be ok??? You do a compression test? Did it backfire or cough while starting? could be a blown port cover gasket or 2. 1 backfire can blow the gaskets and hard starting and poor running...
  14. jerryjerry05

    Gear case cover

    Blue, probably no water.
  15. jerryjerry05

    92 force 90

    Your not answering all the questions?? (Does the motor continue to rev up after you get to 18mph? Check / watch the linkage as you have someone push the throttle forward(turn prop as you push throttle, otherwise the linkage binds). Watch the timer base as you throttle up.) Linkage broken? How...
  16. jerryjerry05

    92 force 90

    More info? Does the motor continue to rev up after you get to 18mph? You have Trim@Tilt ? How big a load are you carrying? Check / watch the linkage as you have someone push the throttle forward(turn prop as you push throttle, otherwise the linkage binds). Watch the timer base as you throttle up.
  17. jerryjerry05

    Runs and Dies instantly

    Take the fuel pump apart???
  18. jerryjerry05

    Gear case cover

    What color was the oil when you drained it? If it's brown it might have water mixed in??
  19. jerryjerry05

    Wont start. Please help

    Check for spark??? You try starting fluid? Clean the plugs or new plugs? These small motors can get flooded and very hard to start since there's no electric starter. Every time you pull the cord your adding gas/oil into a cylinder that has a lot of that already in there.
  20. jerryjerry05

    Replace kill switch or bypass?

    Now that you know the possible year is there any marking ANYWHERE on the motor giving the model or serial#?? On the very Need a side pic of the lower unit and then the coils and if there's a pack or voltage reg?
Top