Search results

  1. alldodge

    Upper shift cable?

    There is a soft alarm is found on a outboard but not able to find it on a I/O. Motor speaker is behind the helm
  2. alldodge

    Care to guess tire size?

    What size and modle is the boat?
  3. alldodge

    5.0 GXI C no start

    The ECM controls the alarm Was blowing a fuse then won't start at times, and not repeatable There is a bad connection or chaffed wire somewhere in the harness is my guess
  4. alldodge

    Dpsm 1.95:1 outdrive toast

    Not a VP guy but don't think the yoke is heal in by a screw. Most are held in by a snap ring or nut and lock ring. So far as what happened, the drive developed a leak and the water damaged the drive
  5. alldodge

    Anti-freeze Question . . . Change of Color ???

    I would remove both water hoses and connect them together during winterizing with AF. Later I just used air with a Reg set around 40 psi and blow everything out
  6. alldodge

    Dealing with bogging for too long and need help because I've done just about everything!

    One of those Doh moments, don't know how I got mixed up. I even posted the pic of the GM 7.4
  7. alldodge

    Dealing with bogging for too long and need help because I've done just about everything!

    It's a VP Ford MPI
  8. alldodge

    Anti-freeze Question . . . Change of Color ???

    Don't know but why not bypass the HW heater after draining, so it doesn't take so much AF?
  9. alldodge

    Tb IV intermittent spark ?$#???

    Everyone says OEM only yet last week there was a guy who installed OEM and had no spark. He bought a cheap amazon knock off for dumps and giggles and it worked. So was it something else, bad connection, other, I have no idea but only reading what was posted. I mentioned to take it back to...
  10. alldodge

    Carb to MPI problem 2011 Merc 4.3

    Not all motors use the cam sensor and appears yours does not
  11. alldodge

    LU 1655-7332 Parts Diagram?

    Have you looked here? https://www.mercruiserparts.com/850-6-cyl--1460999-thru-1766823
  12. alldodge

    Replacement Oil Filters

    I used wix for many years SHORT filter wix 51040 or NAPA 1040 same filter different label LONG filter wix 51036 or NAPA 1036
  13. alldodge

    Tb IV intermittent spark ?$#???

    Any internal resistor coil, and from what I've read it's not the coil Did you run through the troubleshooting post 41?
  14. alldodge

    Key Fob cost

    I know I could find it cheaper and the manual does show how I could program it. I bought new because the dealer couldn't find the 2nd one and said they would reimburse. The older 2012 manual didn't list how to program so I went to dealer
  15. alldodge

    Key Fob cost

    Remember when you had a key and it cost maybe a dollar to get a copy made? While I do like the Fob the cost has gone astronomical. Wife's 2012 Caddy (bought 2014) was bought used and only had one fob. That's BS, so we spent another $200 to get one programmed and key cut. She gets a 2023...
  16. alldodge

    Stainless riser fitment help.. with numbers

    Part number 816900 is only list as V8, the Letter and then number after it is for port/starboard and different motors. Elbow uses 6 each 1.00 long bolts and 2 each 2.30 inch long bolts to secure remote oil filter Your motors original part 807899 uses same for each side. List 8 each 5.75 inch...
  17. alldodge

    FUEL PUMP

    Correct https://www.ebay.com/itm/115175190307
  18. alldodge

    Mercruisier 7.4 litre gas pressure

    Been thinking about this pic This is a block diagram pic to make the system more clear of how it works. Example: the fuel pump is behind the plate, so Reg is also shown separately
  19. alldodge

    Mercruisier 7.4 litre gas pressure

    That's the correct Reg Things don't add up and I would look at bench testing the Reg. Apply air pressure of bottom of Reg with adjustable air Reg. Slowly bring air pressure up to see it should open at 43 psi. Reduce air and then with a hand operated vacuum pump apply vac to port and bring...
  20. alldodge

    Stainless riser fitment help.. with numbers

    Putting stainless and cast iron together is not a good idea in salt. There are mitigation methods I'm not finding enough info on what you currently have to comparing what your wanting to use. Original elbow shows 90*, the part number 816900 is no longer made but I'm finding it's used on V8...
Top