Search results

  1. alldodge

    Starter for 2000 5.7L

    The across spacing is right at 3 inch Staggered 3.25 inch The 3 inch takes a different flywheel
  2. alldodge

    Starter for 2000 5.7L

    ok, but it won't fit your motor
  3. alldodge

    Starter for 2000 5.7L

    Straight across spacing?
  4. alldodge

    VP 5.0 GXI-G SX-A Trim No Power

    Breaker is on the motor or trim pump.
  5. alldodge

    VP 5.0 GXI-G SX-A Trim No Power

    Howdy Trim switch is what energizes the relays which then sends power to the pump Check breaker and fuse
  6. alldodge

    1978 trim motor issues

    Motor repair or replace time
  7. alldodge

    Trouble finding engine model number

    From the pics and numbers it appears to me (note maybe only me) that this is a VP motor that was replaced by a Merc reman. OK, seeing the Holley carb means the Merc reman has had the VP carb, intake and other stuff installed on it. So it's a GL model (2 BBL)
  8. alldodge

    1978 trim motor issues

    Don't see that happening unless the wires are badly corroded You can take the 2 wires on the pump and connect one to + and other to - and it will run one way Swap the wires and it will run the other way It it does that it's not the pump, its connections or switches
  9. alldodge

    Trouble finding engine model number

    Welcome Lets not start a Thread in the Merc and VP sections asking the same questions. Is this a Merc or VP motor. Indicate the drive is VP
  10. alldodge

    1978 trim motor issues

    Thinking it's the switch panel not making good contact. If it makes contact but not enough to pass sufficient current the solenoid will just click Red is the Main hot wire. Connect red to Green on the solenoid with a jumper, if it works then its the switch panel
  11. alldodge

    Crank but No Start troubleshooting

    Pic shows a black wire not connected
  12. alldodge

    Crank but No Start troubleshooting

    Your serial number 0L006627 shows a TBV ignition, Merc carb and electric fuel pump You can hot wire the fuel pump to see if it runs but could also be the oil pressure switch, a ground or corrosion
  13. alldodge

    5.7 GXI-H engine. Alternator problem ?

    With 3 wires then terminal P is not needed and the ALT is wired like most VP motors
  14. alldodge

    Bravo 3 Gear Lube Capacity- 2.5 or 3.5 quarts

    Yes, you probably have a air bubble in there. Just guessing but could probably leave the vent out over night with drive down and level would drop. When vent opened oil from lube bottle is going to come out, then it will take a some time for the air to slowly move from lower to upper. If it was...
  15. alldodge

    Bravo 3 Gear Lube Capacity- 2.5 or 3.5 quarts

    It should hold 3 Quarts. Was the drive left to drain over night or just a short time? Was the drive fully down when refilled?
  16. alldodge

    2006 Volvo Penta 5.7 GI limited rpms

    Welcome Is timing advancing? Fuel pressure is off. Later GXI are 50-60 psi, Gi is same unless it's a old model then it would be 30 psi
  17. alldodge

    Battery Died

    Your Bat should have no problems staying up using the boat in that manor. Your Bat should read 12.6V or above just sitting for a couple hours off a charger. If it reads lower there would be a problem. When motor is running the Alternator output should be around 14.5V
  18. alldodge

    2003 Stingray 230lx Bilge questions

    Bilge pump is not that hard to replace because the old one does not need to be totally removed. Go to local hardware store and get a piece of flat stock aluminum, maybe 1.5 to 2 inch wide stuff. Bust out old pump anyway you need to and remove hose and wires going to it. Attach new pump to...
  19. alldodge

    3.0L MerCruiser, idle trouble.

    Welcome In most cases it will deal with a carb issue. Needs to be cleaned/rebuilt or choke is hanging I would start by removing the fuel filter and dump the contents into a clear container. There should be nothing but clean gas. When motor won't start, remove flame arrestor and see if the...
  20. alldodge

    5.7 GXI-H engine. Alternator problem ?

    I don't know, would need to be there to look
View older results
Top