Search results

  1. alldodge

    3.0L MerCruiser, idle trouble.

    Carb needs a good cleaning, but buying another works most times, just cost more
  2. alldodge

    5.0 MPI Brass Sea Water Pump Bearings

    Have not taken one of that style apart but have rebuilt other style. If you have a press you should be able to replace the bearings This is parts for ones I've rebuilt, cost was cheap. I found aftermarket bearings by searching on Merc numbers
  3. alldodge

    Bogging issue

    It doesn't take much pressure to see something. Carb would be 4-7 psi When the line comes off is it full of fuel or air? If fuel pump the throttle and see if fuel squirts down the carb
  4. alldodge

    gimbal bearing house hit by trailer while emergent braking before red light.

    That's not an issue, made that way. This allows the U bolt to tighten up around the upper steering pin
  5. alldodge

    a carburetor shouldn't spill fuel like this, right?

    I would triple check the float level, most likely a tad bit to high
  6. alldodge

    3.0L MerCruiser, idle trouble.

    The vids are not attached
  7. alldodge

    Reliable sure lube hubs

    ok, then I would treat them as if they didn't have a grease fitting and remove the cap, grease by hand. No telling what is or is not behind it
  8. alldodge

    My boat run slowly. 120HP,2.5L,1989

    How is the distributor cap and rotor?
  9. alldodge

    My boat run slowly. 120HP,2.5L,1989

    I would MR43T
  10. alldodge

    My boat run slowly. 120HP,2.5L,1989

    I showed these to pics to the wife and she has never done any motor work and she sees a difference
  11. alldodge

    My boat run slowly. 120HP,2.5L,1989

    Not bothered by the one at 100, could be anything and not really be a factor when running That said, if your gauge is accurate then the motor may just be getting tired Is the timing set correctly, is timing advancing and if so how much? How do the plugs look, all the same or different?
  12. alldodge

    Single Person Loader?

    search "automatic boat trailer latch"
  13. alldodge

    replacing the inner prop shaft seal on bravo 3

    Many disagree but no way I would try and replace the seals without removing the shafts. Need the tools to remove carrier and seals https://forums.iboats.com/threads/looks-like-im-getting-into-bravo-outdrive-repair.617342/ Would replace with the single double seal and not the 2 individual seals...
  14. alldodge

    Disc Brake Identification

    If your unable to find exact instructions, calipers are pretty much all the same If your caliper rotors are good to reuse Remove caliper If your not replacing caliper, remove master cylinder fill cap but leave loose on top to keep dirt out Use C-clamp and push caliper piston(s) back into...
  15. alldodge

    My boat run slowly. 120HP,2.5L,1989

    We don't know, your going to need to do some testing Suggest Do a compression test How long have you owned the boat?
  16. alldodge

    gimbal bearing house hit by trailer while emergent braking before red light.

    As 04fxdwgi25 said, you have a issue with the transom otherwise the goop would not be on the transom assembly
  17. alldodge

    Reliable sure lube hubs

    Search online, lots of vids, sure lube, eazy lube are all the same, they re not bearing buddies. Only seal is in the rear and not the front. The front is a cover that is removed to lube
  18. alldodge

    Reliable sure lube hubs

    My suggestion Pump grease until it starts coming out. If you see any water then pump some more to expel the water. Take your finger and get all the grease out of the hub so there is an air gap. You cannot remove enough to do any harm but if you don't give it a air gap the grease will heat up...
  19. alldodge

    Disc Brake Identification

    I'm finding the UFP DB-35 is a 12 inch diameter rotor and the DB-42 is a 10 inch Scratch that the 35 and 42 both have a 10 and 12 inch disk Depends on lugs, size and material
  20. alldodge

    Dean's List gets another motor

    Most everything is back on the motor, including injectors and rail (not shown). Waiting on a thermostat for couple weeks. If we don't get it soon we're going to use the old one.
Top