Search results

  1. alldodge

    Adding a Battery isolator

    What do you mean in between Bat 1 and 2?
  2. alldodge

    Bravo 3 Shift Cam Position

    No issue with the clunk, motor turning at 600 RPM and clutch engages gears and starts turning a prop
  3. alldodge

    Adding a Battery isolator

    Your saying Isolator and sketch list VSR and pic shows a Relay but calls it a Voltage Sensing Isolator. BTW - Vervor is a China company that sells lots of stuff, basically middle man
  4. alldodge

    So I ended up sinking a bit.eek! 82 sea ray

    Being a 1982 it's probably a 140 and has either a points distributor or Digital ignition (DDIS) Guess not knowing much we would have trouble helping there unless you can get info as to what is happening.
  5. alldodge

    1993 5.0 EFI Fuel Issue/ Hard starting

    Looking at what I have for a wiring diagram, the FP is energized by the ECM. The ECM applies a ground to one side of the relay coil. The issue is I don't know if it turns ON like newer Merc/VP or if only during cranking. Measure power on both sides of the coil (pins 85 and 86). Do this when...
  6. alldodge

    So I ended up sinking a bit.eek! 82 sea ray

    What motor?
  7. alldodge

    a carburetor shouldn't spill fuel like this, right?

    OP pump is electric, your talking about the mechanical pump
  8. alldodge

    2001 Johnson 70

    How's the compression?
  9. alldodge

    1993 5.0 EFI Fuel Issue/ Hard starting

    Don't make multiple threads in different areas, they have been merged
  10. alldodge

    Changing my boat gauges.

    All gauges should have full Bat voltage, only the sender wires would have less. If ground is bad (probably is) then taking a reading will be off. Use a jumper wire from Neg Bat terminal to the meter and then take readings.
  11. alldodge

    2010 350 Mag MPI bravo 3 gaurdian mode issue. 5% power

    No officer I didn't steel it, no one saw me do it I'm sure
  12. alldodge

    shift issue and running with some noise from lower unit gear

    Should never start or run that high, that was the U joints banging around
  13. alldodge

    shift issue and running with some noise from lower unit gear

    Your drive is to high, does it reduce when it's lower?
  14. alldodge

    VP SX 3868584

    Call any VP dealer or searching for the part number online and it comes up. Looks like over 10K
  15. alldodge

    shift issue and running with some noise from lower unit gear

    Your not going into throttle only. Try this, move shift to neutral, grab the bottom of the shifter and pull out. It should move out toward you, then move handle forward
  16. alldodge

    shift issue and running with some noise from lower unit gear

    4 buttons? I see 1 switch with 2 buttons If the handle button does move in and it's not disengaging the shifter, then it needs repaired or replaced
  17. alldodge

    a carburetor shouldn't spill fuel like this, right?

    Don't know which V6 other then one with a 4 bbl Find the original fuel pump was 805656A5, is this the pump your have? Put a couple gal of old stuff in a full tank and the truck should not have much issue, or run it in the lawn mower, but even the mower can have issues
  18. alldodge

    shift issue and running with some noise from lower unit gear

    I don't see a throttle only button on your shifter. Yours should be pulled out in neutral then moved forward for throttle only
  19. alldodge

    5.0 MPI Misfire Under Load

    What's your serial number?
  20. alldodge

    1987 OMC 2.3l Bluefin 1900 Sportsman wiring

    Other then standard wiring practices we're probably not going to find anything to help. I would suggest as you thought of and just replace the fuse panel with something like the Blue Sea model
Top