Search results

  1. alldodge

    1987 OMC 2.3l Bluefin 1900 Sportsman wiring

    This is what I found, and could also check on forum "The Hull Truth", those guys are mostly offshore boaters https://www.bluefinboats.com.au/contact-us
  2. alldodge

    Engine Alignment tool goes in about 1/4 of the way, question.

  3. alldodge

    1987 OMC 2.3l Bluefin 1900 Sportsman wiring

    Being a Blue Fin there may be a wiring diagram but finding it will be the issue. Have you tried to contact Blue Fin in Australia?
  4. alldodge

    1994 Astro S-18FS (won't start)

    Welcome aboard Moved your thread to Merc OB's so it will get more views
  5. alldodge

    Location of fuse box on OX 66

    You mentioned Bondo said So were talking about maybe a breaker without a reset part so "auto-reset breaker" came into the discussion
  6. alldodge

    Location of fuse box on OX 66

    Sir, let's simmer down and not lash out from what you think is being said
  7. alldodge

    Dean's List gets another motor

    Brand new never been used crank, don't know what a flap wherl should be able to do
  8. alldodge

    496 bravo 3 3000 RPM plus overheat

    Yes, I sold the Formula to a guy in Naples FL. He has been enjoying it, and I was just real tired of hanging upside down to change impellers and other things. Having OB's it should be much easier for this old guy Here is my Bravoits fix but then again I never had the issue being in fresh...
  9. alldodge

    Location of fuse box on OX 66

    Search auto reset breaker, you will find them It's basically a temp breaker. Current passes thru contacts until it gets so hot that the breaker contacts separate. When it cools back down contacts pass current again. Used a lot on heavy equipment
  10. alldodge

    Dean's List gets another motor

    Original motor is stripped and put back in the crate. Started putting things back on rebuild and 2 issues came up. Oil port below the distributor had a plug installed by the machine shop, WHY we have no idea. Would not be a major problem but the dog turd guy also used some kind of loctite and...
  11. alldodge

    2013 Volvo Penta 4.3GL Oil Pressure Drop & Valve Tapping / Rattle

    Lifters will not cause pressure to drop
  12. alldodge

    2000 5.7 gsi fuel pump relay problem

    There is no ground being applied by the ECM "or" there is a break in the wire. Always thought Bob did a good test but not felling good about this. Look real close at the pin on the ECM and make sure its making connection. If it is contact Bob and ask him about it, this is really the only...
  13. alldodge

    2000 5.7 gsi fuel pump relay problem

    Take a light bulb and put 12V on one side leave the other side disconnected. Put the negative meter probe on the negative battery post. Now if you take the positive probe and put on either side of the bulb you will read 12V because the other side of the bulb is not connected to anything. If...
  14. alldodge

    2000 5.7 gsi fuel pump relay problem

    Yes, but only for a couple seconds when key is first turned ON. Once ECM removes the ground you will see 12V again Did you tell Bob that it was a fuel pump issue? Not that he needed to know but I'm assuming it would help make sure the problem your trying to fix
  15. alldodge

    01 SeaRay 6.2 MPI intermittent no crank no start

    Sounds like a bad connection. Disconnect and clean to shinny metal on both ends of both battery cables, including the ground. Then disconnect the 10 pin engine connector and clean the pins
  16. alldodge

    Wheel bearing grease "oozing"

    Think the seal on the bearing buddy may be the issue
  17. alldodge

    1993 285 Exhaust question

    Most drives have what's called relief ports in the lower side. Alpha drives have then in lower transom assembly. My guess is omc has similar
  18. alldodge

    1993 285 Exhaust question

    Moved to OMC because it's about the drive and not the boat
  19. alldodge

    2013 Volvo Penta 4.3GL Oil Pressure Drop & Valve Tapping / Rattle

    If your loosing oil pressure it's not normal and 10w40 should be plenty to keep it up. Put a mechanical gauge on the motor to verify pressure is dropping and if it is then there is a problem.
  20. alldodge

    350 Mag Mpi hard to start when warm or hot

    We're still guessing, need to scan the motor and see what is happening
Top