Search results

  1. K

    1986 Bayliner Capri AQ131a, timing belt intermediate pulley is off position

    Most likely in the past the belt was replaced and the distributor‘s wires were moved around to compensate. Since the genuine Volvo belts are marked it is not hard to line up everything. Sometimes when the belt tensioner is released it will cause the belt to jump a tooth on one of the...
  2. K

    Another prop slipping thread

    Once the dog is locked in any gear there is no way it would slip. I am bettering on the drive coupler. Especially after the propeller has been ruled out. Full power starts pulling people really puts a lot of strain on the coupler. Upper or lower gears do not “repair themselves “ after the...
  3. K

    Ignition timing specs volvo penta aq125a

    You need to clean the carburetor. Most times the gaskets are reusable if this is a down draft carburetor. The idle metering screw is always 1.5 turns from seated. Most times 1-1.5 turns on the stop screw. Anything more than this is not right.
  4. K

    Ignition timing specs volvo penta aq125a

    If you have a new belt from Volvo it will have yellow marks that line up with the marks on the sprockets. Remove the spark plugs after the belt is installed and turn the engine by hand around enough revolutions where the marks will work themselves back to where you started. This certifies that...
  5. K

    VP 280 no reverse

    All the parts in the picture that SD posted can be replaced with the exception of #41 with out removing the drive. You need a Volvo Genuine parts and a service manual.
  6. K

    Fuel system problem on 13 yo storage boat

    There might be a fine screen filter inside the tube, be sure to remove and pitch it.
  7. K

    7.4 Bravo water pump driven fuel pump

    The Carter is by far better than the Holley. They cost more for a good reason. You want the oil pressure safety switch also.
  8. K

    VP 280 no reverse

    The brass trunnion with the cotter pin on the main cable. That is what you need to adjust. Leave the other control rods as they are.
  9. K

    Alignment and coupler question 1979 Mercruiser 260

    With a small bottle jack under the front of the engine to raise it, remove the top nut then the lag screws holding the mounts after the mounts are out remove the bottom nuts and reinstall the mounts. Raise and lower the engine with the jack until the alignment is right. If there is space under...
  10. K

    VP 280 no reverse

    Put the control in neutral, remove the cotter pin from the brass trunnion. With the drive in neutral rotate the trunnion until it centers in the stainless lever. If it still does not move enough for reverse then the cable itself may be the problem or the control box.
  11. K

    Valve Adjustments

    If your engine has a roller cam they should not need adjustment. If the timing cover is plastic rather than metal then it will have a roller.
  12. K

    How do I fill the intermediate housing?

    There was no drain until the first 400-800 units in 78.
  13. K

    When my boat is on the trailer, this happens.

    It looks like the reverse lock valve has been bypassed. That is most likely the cause. Later model pumps have the reverse lock valve in their valve body. The valves tend to leak externally and this one is from the late 60s to early 70s. The valves are NLA and used ones are a crap shoot...
  14. K

    When my boat is on the trailer, this happens.

    Does the plastic hose go to the reverse lock valve on the shift linkage? Are the rams the original to the boat? Post a picture of the rams and the shift linkage .
  15. K

    In-boat camshaft replacement - 7.4 Mercruiser

    Place a strong magnet on the oil pan to hold the small chips from the worn cam and lifter. The Grey RTV will also seal the lower timing cover seal area in place of the original rubber strip as well as the china walls of the engine block to seal the manifold. I also always go around the outside...
  16. K

    New Motor same power issue

    HEI distributors require more amperage than the original Mercruiser ignition system. When the HEI is on a GM auto it is fed with a #10 gauge wire. Try jumping from the + side of the battery to the + side of the HEI with a #10 gauge wire and take the boat out to see if that helps. If it does...
  17. K

    87 OMC 5.7 No Spark

    The only thing I can suggest is according to Prestolite their system is not compatible with OMC‘s esa shift system. Try reinstalling the original Prestolite points and condenser. Also try connecting a volt meter to the + side of the coil while running the boat to see if there are any voltage...
  18. K

    When my boat is on the trailer, this happens.

    Try to post a picture of the hydraulic pump.
  19. K

    1987 Volvo penta aq125a starting problems

    Sierra Marine #. 18-5292. This is what fits the Bosch distributor.
  20. K

    1987 Volvo penta aq125a starting problems

    The points should be .020 and the plugs .035.
Top