Search results

  1. alldodge

    Maybe my turn for new boat time

    The deck is dirty because I'm not taking off my shoes yet. To many in/out's arranging things, but it is gelcoat. The boat has just 2 Bat switches (Engines and House) and when their turned on it takes a few seconds of their red led flashing before they go solid. Then things can be used...
  2. alldodge

    Nav light bulb replacement

    Don't know and been unable to find one like it, but have seen them many times. I would guess the white top piece is snapped on. See if something thin can be slide between green and white on top In most cases its a bad connection and not the bulb. Most folks don't run at night enough to burn...
  3. alldodge

    6.2 fuel injection problem

    What's your serial number?
  4. alldodge

    Maybe my turn for new boat time

    First thing we did is remove the Dealer info off the trailer and boat (n)
  5. alldodge

    Maybe my turn for new boat time

    Yes, but its either white or black, and we want blue The guy doing the canvas has done other things for us and he does great work
  6. alldodge

    Intake manifold verification

    Then should be no problem. What ya run into is just finding something for a 302, but with closed cool it can be treated like a car
  7. alldodge

    Intake manifold verification

    You need a marine intake but could get by if in fresh water (for many years) or if closed cool. If in salt there is no way
  8. alldodge

    Maybe my turn for new boat time

    Pick her up and she's now in the barn, probably post some pics tomorrow Hope its not an omen, just left the dealer and first stop I feel a heavy clunk as the trailer hits the stops (surge disk brakes). Not good, call dealer and advise I'm head back. Tech looks under trailer and finds 2 on the...
  9. alldodge

    Ground fault with black wire melting

    With a boat next to nothing is every easy
  10. alldodge

    Mercury 4000 side mount remotes unit issues

    Doubtful but can always ask
  11. alldodge

    Ground fault with black wire melting

    Agree there is a short Might get some strong nylon string/cord and tie to end of wires, then pull wires out other end. The cord will allow new wires to be pulled back thru
  12. alldodge

    Question about installing new clutch/gear set in 1999 Bravo 3

    No expert but my understanding is the TW is applying its torque the the square drive area. It measures at the square drive and is calibrated for the wrench flex. The longer the wrench the more flex, shorter less flex
  13. alldodge

    Banking Software

    I do the same
  14. alldodge

    Engine alignment ,just got the tool. Pics posted

    What I'm understanding now is your probably good to go Mine only cost about $20 so no issue with the cost, only if it was made correctly. Having uniform marks is a good sign
  15. alldodge

    Engine alignment ,just got the tool. Pics posted

    It's I doubt the vibration is caused by misalignment Getting no marks means the coupler is shot (Doubtful because boat was moving), or your not getting it actually into the coupler Take something long and skinny (stick, dowl rod, other), put it the bottom of the coupler and mark the end of it...
  16. alldodge

    Deck Repair - Fiberglassing Question (Newbie)

    What your discussing could work but need to cut out the spot first to find out what made it soft. Once it's cut out you may find the issue goes out further then what your seeing now. Most places show up after other things start happening below
  17. alldodge

    Ns90a idiot mistake

    Don't know what shorted out, but most likely it was the ignition system. If it was a Mercruiser it normally is the ECM
  18. alldodge

    too much outboard for the boat?

    I would start with what is max HP for the boat then find out how much that 2 stroke weighted.
  19. alldodge

    Engine alignment ,just got the tool. Pics posted

    The mounts should be done equally only if they are equal to begin with. If one was turned more then the other then the twist starts. If unsure, with boat seating level and both top nuts loose. Lift motor up slightly by the thermostat housing bolts so the mounts are not touching the bottom...
  20. alldodge

    Building A Mercruiser 350 Few Questions.

    Thinking the last digit is 7 14096217...55-86...350..........Crate motor, 285hp/300hp, 64cc chambers, 72' or 90' center intake manifold bolt angles
Top