Search results

  1. dwco5051

    Drain plug question

    If it will come out just #1. As Scott said if the plug doesn't come out with out a lot of force replace the whole thing (1 & 2)
  2. dwco5051

    Drain plug question

    I can't tell from you picture if that is a 3/4" or 1/2" plug but if you get it out ok consider getting two nylon plugs as replacement. Why two? Keep one in the glove compartment of the boat because sooner or later someday you will go to launch and remember you left plug #1 on the workbench at...
  3. dwco5051

    Drain plug question

    Been there, common problem. That plug is a tapered pipe thread and once the initial corrosion bond is broken it will unscrew easily. The tapered thread is designed to be leak proof so it is hard to get any solvent into the threads. Try putting pressure on it with a wrench and tapping the...
  4. dwco5051

    What's the difference between QL77JC4 and the QL82C

    Or 1950 when every angler kept a least one spare set of plugs in their tackle box. One quart of Gulf motor oil to 5 gallons of gas was the mix for my motors for years. Never owned a 50:1 motor until I bought a new Mercury 850 in 1977. In 20 some years only changed the plugs (surface gap)...
  5. dwco5051

    Trolling motor not move boat fast enough in my opinion.

    It sounds like you are not getting 24v and only running on 12. You should almost be able to ski behind a 17' bass boat with 82# thrust. Is there a rocker switch beside the plug on the panel marked 12/24? My older 20' Nitro had one and it was for a charger plug that would plug an adapter...
  6. dwco5051

    Elgin 5HP motor

    Don't know what year that motor is but if it is one of the air cooled Eska built models the water pump only pumps water up into the lower leg to cool the upper seal. Does your motor have holes on the sides of the leg like the one in the picture? If so that is what the arrows are pointing to...
  7. dwco5051

    Rec gas prices???

    Here in Pennsylvania they use a formula to figure how much gas was bought by boaters. That amount is transferred from the DOT general fund to the Fish & Boat Commission boat fund. The monies are used for boating safety education, aids to navigation, boat law enforcement, access and launch...
  8. dwco5051

    Looking for Tracker Targa Transom Corner Cap

    Local weld shop could fabricate that. Since you have the one side it would be simple to make a pattern for the port side. Probably 5083 or 5383 plate. Any shop with marine experience could fix you up.
  9. dwco5051

    Nada Guide

    True value is what one willing buyer will pay to one willing seller for an item. Book value is based on collected data of the average selling price of an item. I suspect that NADA values or based on a small percentage of the actual number of sales on that item. Statistic calculations accuracy...
  10. dwco5051

    Fuel Consumption - Is This Right?

    My mistake: Change mpg to fuel burn rate . My brain got ahead of my fingers when typing this . Thanks Scott, missed that when I first proof read it. Another senior moment.
  11. dwco5051

    Fuel Consumption - Is This Right?

    There is an old rule of thumb that mpg at full throttle is equal to 10% of motor horsepower. In you case 6 mpg. Those older OMC's were known as fuel hogs so depending on many things including loading, prop, engine age and on and on you are probably in the ballpark at 4. What is the max HP you...
  12. dwco5051

    Power drops at console when hitting switch/turning ignition

    If you haven't done it already remove and clean your battery connections. Sounds like a corroded connection or the main wire off the battery is corroded at the connector. You have just enough of a connection to power a voltmeter but any higher amp draw fails. Just ran into the same type of...
  13. dwco5051

    Miserable Midwest Spring

    Same up here. Lake is 8 feet above normal recreation pool. This is my usual ramp with water up in the parking lot.
  14. dwco5051

    Homemade Strap Wrench

    How to make a quick & easy strap wrench from an old spark plug socket, worn-out poly-V serpentine belt, and a short length of PVC 1/2″ schedule 40 pipe. Use an angle grinder to quickly slot opposite sides of the socket. Fit the belt thru the slots and then tap a short length of PVC pipe into the...
  15. dwco5051

    Hi all, just purchased a14' aluminium v-hull boat with no hull ID. This is all i found. Can somebody help identify the year and manufacturer?

    Coachmen industries of White Pigeon, MI in1968 acquired Viking Boat Company, Search the internet for images of Viking 14 foot Aluminum Boats and there are lots of pictures. See if any look like yours. Read more...
  16. dwco5051

    Just purchased the new Lowrance HDS9 Live Fish Finder, I have a transducer question.

    Hard to say with out seeing where it is mounted. Is it mounted so high that it is out of the water at moderate speeds? Is there something directly in front of it causing turbulence? Need a picture to help. Also take a look at...
  17. dwco5051

    Help with alarm and alternator

    Don't know about your motor or wiring but things have changed since I was a kid. My truck controls the solid state regulator in the alternator by a signal from the powertrain control module (PCM) That signal comes from the PCM as a clipped signal and the charging rate is controlled by the...
  18. dwco5051

    Random

    I don't even look at the person in the mirror. It is the image of some old white haired guy that doesn't even look like me some how on it.
  19. dwco5051

    Hey Newbies

    Like the message that was on the forum for my home lake a couple of evenings ago; "Was planning on going out in the morning. Lost all power to my boat while installing an ignition switch today. If anyone has any input or knows of someone that can fix my problem it would be greatly appreciated"...
  20. dwco5051

    What tools needed to check over an old project bass boat before buying?

    Here is the page on how your system works. The factory manual does not tell how to test the system without having their analyzer so you have to go by the CDI instructions.
Top