Search results

  1. C

    Water pump issues

    One more thing, on the old water pump, I put a hose on the pump to flush it backwards, water was leaking from the drive shaft. I'm thinking, if the impeller is pressed in tight, how would water get past the impeller? This test was low pressure water
  2. C

    Water pump issues

    I'm working on a 1993 manier 75 hp Boats been sitting for a long time, I get it started, water pump not working, removed lower unit, flushed the motor from the bottom with a hose, a little dirt washed our, than ran clear. Replaced complete water pump housing, impeller gaskets. The kit came...
  3. C

    Electrical pronlems.

    I'm thinking of everything. The emergency disconnect on the control was wasn't stopping it from starting before. Can I by pass it for now too see if it's killing all the power?
  4. C

    Electrical pronlems.

    This generic diagram shows a fuse at the motor, the only one I've seen was a old glass bulb type, I cut it out and installed a new blade type. There is power at this fuse.
  5. C

    Electrical pronlems.

    93 manier 75 hp Working on a boat for a friend, drops it off, not running, and has been sitting for a few years, replaced bad stater (copper wire on brushes came lose) got it started, replaced water pump, linkage was jacked, someone connected the throttle on the wrong side, idle position was...
  6. C

    93 manier 75 hp

    Is the plastic part like a cover to hold cables in place?
  7. C

    93 manier 75 hp

    It's remote controls
  8. C

    93 manier 75 hp

    I'm looking for a part or part name, for the plastic piece that holds the shifting cables in place on the side of the motor, it held on with 2 push pins. I don't have a model number, And it's not shown on the parts diagram from retailers. Like Crowley's
  9. C

    96 johnson. Link and sink

    96 j150exedb The trunion nut is maxed out. I leaned a new word. Lol
  10. C

    96 johnson. Link and sink

    96 johnson exeedb 96 johnson 150 exedb
  11. C

    96 johnson. Link and sink

    The cable is not long enough to hold the roller against the timmer plate. I rebuilt the motor, same cables from old motor. The only thing that could have happen, i used linkage parts from 95, mines an 96, I would have never thought they were not the same motor
  12. C

    96 johnson. Link and sink

  13. C

    96 johnson. Link and sink

    I have set my like and sink, with the cam roller touching the timmer base, it starts and idles, when i connect the cable, it pulls the roller off the timer base 1/4 or so. In this position, will not idle, I had bought a new control box during my build, Should this motor idle the the rolled of...
  14. C

    96 johnson timing.

    I had the boat idling on a hose at 900 rpm. I took it to the lake and it will not idle. Useing a timming light, i can not get the idle timming below 10 degrees btdc. It should be 4-6 atdc No matter what i do, i canr get it firing atdc. At wot it hits 20 degree as it should. It will barely idle...
  15. C

    96 johnson timing.

    Only for v4 using #2 plug
  16. C

    96 johnson timing.

    The manual gives 2 options for timing,) if you can see the photo) I have rebuilt the motor and it starts and idles fine. I'm putting it in the water tomorow to set low and high timing. With the motor warm, should it be set at 4-6 btdc? or 4-6 atdc for normal operation? If i understand...
  17. C

    Cooling problems

    Ok., i have my new water punp. Looking at the service manul, it shows the order to installing the pump Reading the pump installment instruction are different. Here are 2 pic. Pump supplier call for number 10 and 11 Manual call number 10 only.
  18. C

    Cooling problems

    I put the thermostats in water on the stove, they both opened about 145. I just replaced the cup and impeller. I did notice the cap didn't seem flat, I was having problems with the new house and rubber gasket staying in place. so, I used the old one. I'm ordering a new pump and will uses all of it.
  19. C

    Cooling problems

    Up date. I tested the t states at 145 +- they are good. Idle 1000 rpm post is running 120 to 130 Starboat side 150 +- At 800 rmp they both rise but starboard side close to 170. Then i shut it down. This on the hose. I dont think the tell tale is not puting out as much water as it had last...
  20. C

    Cooling problems

    I have the manual. I beleive you have answered my question. My test was without the t stats. I was thinking one was bad so i removed it. I will test them today and see it they open at the right temp before i install them. Thanks For your reply.
Top