Search results

  1. C

    Cooling problems

    I rebuilt it this winter. It starts and runs?. It runs good. Was taking it to the the lake to set wot timming. When the water was flowing good, i had concerns the port side ran cooler. But starboard side was warmer. Its pumping water, but its not getting to the power head. It leaking somewhere...
  2. C

    Cooling problems

    I pulled the the lower unit put, removed everything. I was missing the garment inside the wp hose housing. I put it back on the muffs. Removed the thermostates and the plugs for them. Its peeing 1/4 the water it should be, the same as the last pump. I have water coming up and pouring down...
  3. C

    Cooling problems

    The last last one ran about 10 minutes, i said 20 but it was closer to 10 if that matters when runnig dry. Ot did not show any signs of damage, did not has any rubbing scars, ss plate and cap look good. But i went a head and install the new. Im fixing to pull it and if i missed somthing. How...
  4. C

    Cooling problems

    I bought an after marked control box. I could find the wire by color and add one.
  5. C

    Cooling problems

    The last one is brand new, i only ran it long enough to see if it was gong to pump water. It was not ran but about 15 to 20 seconds, so it didn'd burn up.
  6. C

    Cooling problems

    Yes, book said to seal the top and bottom of the gaskt for the wear plater. O ring gets 4 drops, one a each corner to avoid blocking the primer hole. Oring under impeller and key in the slot. Its the same extion i had before. I can fell the water tube be pushing into the pump. I have pulled...
  7. C

    Cooling problems

    1. It ran 2 minutes max without water. 2. I dont think it has an over heat alarm. Its plug in the harness but i dont now where it would located. 3. Motor is rebuilded with less than an hour run time. Motor starts right up and idles good. i havent test compressi because motor run good.
  8. C

    Cooling problems

    This a total rebuild on 96 Johnson j150exedb. I finally got the motor running 800 rpm and water pump building up good pressure, but with the hose Muffs. this was my second water do to my mistake. Wednesday, I had finally got the boat ready to take to the lake to set the timing at wot. Thursday...
  9. C

    How to disable quick start on 96 Johnson 150

    I need to set my timing with quick start disconnected. Why does the manual show the motor firing @ 6 degrees after TDC, and 19 to 20 degrees btdc (it's always before TDC for automobiles.) Mine is idling warm at 6 degrees btdc @ 800 rpm
  10. C

    96 Johnson 150 Setting idle

    I have, just have not recieved it yet, for now im using Selco. I cant find the wide open throttle timing in this book. It referes to using an analyzer. Im using a timing light. Joe says it should 4 degrees less than the manufactors setting. But i cant fint the settings.
  11. C

    96 Johnson 150 Setting idle

    I have done a rebuild on my boat and motor. I bought a new control box. After setting the timing wuth a light?, adjusting link and sync. My idle is so low. Tack reads 900 but its old and notice it was showing that with key off, however it reads an increase in rpm. 1000 sounds better. I belive...
  12. C

    Timming a j150exedb

    Some one posted a link to an artical about timming useing a timming light at idle and wot. Can you repost it? Thanks
  13. C

    Test propeller

    Im wanting to buy a test prop for a johnson 150. Are they generic? If not is there a moddel ?
  14. C

    96 j150exedb. Water pump

    Its done and running. I took the top garment and used black tape under an over ot about an 1/8 in. Slide it in there and bolted it up. I used s hoist this time. It allowed me to push it a little at a time. Thanks guys for the tips.
  15. C

    96 j150exedb. Water pump

    I flushed the motor throug the tube with a water hose with the t stats out. All clear I pulled the impeller out. Its fine, reinstalled the black wedge with impeller. I hand turned the drive shaft. Turns fine.. Im thinking the upper tube garment is laying over and blocking the water flow...
  16. C

    96 j150exedb. Water pump

    I havent, but its next on my list. Should i pull the t states from both heads?
  17. C

    96 j150exedb. Water pump

    Problems, I ran motor on muffs at high rpm. Impeler melted. Replaced inpeller, no water. Remover LU again. Impeller was turned backwards is my guess, it shered the white shim. Installed the impeller the right way. Still no water.. From what information i get online or from manual doesn't help...
  18. C

    96 johnson j150exedb. Help with hoes location

    Thanks, i will try to find me a service manul
  19. C

    96 johnson j150exedb. Help with hoes location

    Thank for your help. I have a couole of more questing On page 3-40 1. The manul reads, connect the recirculatin hose to the hose, does refer to up and lower teed together? 2. Where is the pulse limiter valve? 3. Is this motor conciderrd a looper 4. Does this motor have cylinder block check...
  20. C

    96 johnson j150exedb. Help with hoes location

    I finished building motor i started a couple of yeas ago. I know the the fuel in, oil in , and pules limitter all connect to the bottom of the VRO and the 2 primer lines I dont know what hoses connets to the upper and lower barbs on the front a of the crank case cover. And I dont know...
Top