Search results

  1. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    the 59 housing would fit.----Along with the seal for a 59 model 10 HP.
  2. R

    80s Johnson 110hp does going into gear

    Saabu----You need to find a manual with a starting procedure for this and your motor !!----Pumping the throttle does absolutely nothing on these carburetors !!!!----There is no button to push in on his remote control !!!-----
  3. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    Part # of the seal you are installing?
  4. R

    Loss of power, won't plane

    Head gaskets are correct.----I am too far away to help with finding the blockage.----The saga continues.
  5. R

    1968 Evinrude 5HP Angler will start after a few pulls and run anywhere between 2 and 10 minutes then shut off.

    Did you replace water pump impeller ?----Did you inspect fuel pump diaphragm?-----Did you clean the carburetor ?------Did you replace head gasket ?
  6. R

    Loss of power, won't plane

    Post pictures of top of cylinder heads.------Showing the tabs on the top of the cylinder heads.
  7. R

    Loss of power, won't plane

    Water comes out of those hoses on the way to the thermostats.----When you start the motor water comes out those hoses.
  8. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    You need to replace that bearing housing !!
  9. R

    1976 Johnson 9.9hp forward gear issue.

    It was clearly stated that the lower rod should be fully threaded in.----Just incase you questions the level of help here, I started working on outboards in 1968 and have more than 1 of those lower units on the shelf.
  10. R

    Loss of power, won't plane

    Fact----The water that comes out the tell tale does NOT circulate through the block.----You should have lots of water coming out of the hoses before the water visits the thermostats !!----Time to stop running this motor and find out where the blockage is !!!
  11. R

    Merc 40 Force - Takes forever to start

    It is an enrichment valve shown in the parts book.-----Not the same as a choke solenoid that pulls choke flappers closed.
  12. R

    1976 Johnson 9.9hp forward gear issue.

    No it should be fully threaded in.----Only backed out to line up the bend in the rod with brass connecter and upper rod.
  13. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    Looks like the bushing for propshaft is damaged as well.----I would look for a new seal housing.----Lots of those around.----Did you file bumps around the drive pin hole before you hammered the bearing housing off the shaft ?
  14. R

    Evinrude 15 1992 carburetor cover change

    The motor won't idle ?----What trouble shooting was done other than blaming the carburetor ?
  15. R

    1976 Johnson 9.9hp forward gear issue.

    The parts look just fine.----Or ----There is NOTHING WRONG with them.----So the issue is in adjustment.----Is the lower shift rod fully screwed into the lower unit.?-----Are notches on shift rods lined up before the bolt is put in ?
  16. R

    Water pump 2011 Evinrude Etec, 75hp

    Same impeller from 1980 to 2011 for all the V-4 -V-6 -V-8 models and E-TEC like yours..------Unless you are running in lots of sand / silt , a new impeller is all you need.----5001595 is the kit # and get factory parts.
  17. R

    Need help identifying carb part

    Just $10 in some shops that have parts motors on a rack.-----Make some calls.
  18. R

    Loss of power, won't plane

    It is a woodruff key.-----But it must not stick out too far.-----The key puts the flywheel in position for proper timing.-----The flywheel is driven by the locking tapers, when flywheel is torqued to 102.5 FT LBS.----Therefor tapers must fit properly.---Use lapping compound to...
  19. R

    80s Johnson 110hp does going into gear

    The fast idle lever does NOT allow full throttle in neutral.----It appears to be working as designed.---Is someone turning the prop when shifting with motor stopped ?---Does timer base rotate slightly when using fast idle lever ?
  20. R

    80s Johnson 110hp does going into gear

    Remove motor cowling.----Raise fast idle lever all the way.-----You should see linkages move and timer base rotate a little bit.-----
Top