Search results

  1. S

    1991 20HP Evinrude no acceleration

    Seems like a good motor, just has some kind of gremlin. This may seem a stupid question but is your primer knob pushed in? Hard to tell from the video.
  2. S

    Evinrude year

    Did you look under the flywheel or are they all missing?
  3. S

    1995 E70TLEOR wont run

    Sounds to me you lost a cylinder. Did you do a second compression check after the head gasket?
  4. S

    Johnson 8 pusher prop

    Yeah, I saw those too. My bet it's the 9 1/4 by 6 1/2. It's the biggest diameter, smallest pitch and is unavailable. I've never seen one on a Evinrude. Yamaha t9 and stuff but not rudes.
  5. S

    Johnson 8 pusher prop

    Racerone or whomever, Outboard...J8SRLEDS so 1996 extra long shaft. This is the prop on it. Can't find any info on them and can't read the size. Stock paint seem to have covered up the markings under the cone. Didn't really see anything on the parts breakdown either. Let me know. Thanks
  6. S

    Two wildly different compression readings, why? On in around 60 and on around 200?

    I've never heard of a reading so high, can water actually do that?
  7. S

    1972 johnson 75hp lift assist issue

    Here is some used ones on eBay. $70 plus shipping. Not sure if those help when raising...
  8. S

    1972 johnson 75hp lift assist issue

    Here is the correct part number for a 1974 70hp and while expensive they are available. The other ones I sent you were not available.
  9. S

    1972 johnson 75hp lift assist issue

    Forgot to post this.
  10. S

    1972 johnson 75hp lift assist issue

    According to my chart 1975 is the earliest they made a 75 hp. They show a shock abs and spring for the 20 inch model but different part number than you list. 2 per unit. Should help going down not sure on the up. They do sell an aftermarket lever that you put on the engine cover to help lift it...
  11. S

    1986 6 hp Johnson Gearcase Cover and Seal

    I assume you are installing gasket 324637 keeping the gearcase sealed on the top. No sealer should be required but I don't think it hurts either. Let's see what others say. As long as you have that part out did you replace the other seals?
  12. S

    Starter Bolt Size

    All three should be the same. 1/2 bolts, not sure of the thread though. Looking at your motor with all the Allen heads and stuff maybe someone had to tap that out.
  13. S

    50hp electric start evinrude reverse issues

    I did not know that. Thanks
  14. S

    50hp electric start evinrude reverse issues

    The c and the i represents 1981. Engines don't have titles, are you looking at your boat title?
  15. S

    1974 evinrude 135hp starting and staying on problems

    Well you kind of rambled there a little bit but I will attempt. Motor was stored along time, started with starting fluid..... My guess is you need to go through the carbs. Most will say do not use starting fluid you could burn it up.
  16. S

    Yamaha 225hp ox66 tilt and trim help

    I know that happens to me too, I'll read a couple of threads and then cross them up. Age thing I think!!
  17. S

    Is this normal for water to come out these 2 holes?

    Exhaust vents out the prop unless it has to much back pressure and then it vents out the holes. Can't tell your water level is but make sure it's up far enough....(above the pump aways)
  18. S

    Yamaha 225hp ox66 tilt and trim help

    Not sure what 99 is saying because you made no reference to the relay clicking. Here is where some Yamahas hide the fuse. Port side front in a box.
  19. S

    Yamaha 225hp ox66 tilt and trim help

    Did some more digging and it is fused. The red wire going to your relay should be hot without the switch being used so if it's not you have no power for some reasons. Still betting fuse. Here is a way to test you relay next time.
  20. S

    Suzuki DF115 transom (Trim/Tilt) saver??

    Agreed
Top