Search results

  1. Rranger

    Gelcoat

    Thank you sir.
  2. Rranger

    Gelcoat

    Sanded boat right down to original gelcoat. Dumb question of day. I plan three or four coats of gelcoat rolled on my topside. I only have waxed gelcoat, can I roll on multi coats of waxed gelcoat while still tacky without sanding or do I have to use unwaxed resin and then waxed on the final...
  3. Rranger

    In the process of Sanding?

    A question experienced painters might find humour in but it’s serious. I got a 11 foot by 6’ deck and another 5’ by 3’ deck under the bow to gelcoat. Plan is grit in the gelcoat for slippage and some web solution at the end for show. Two coats of gelcoat for sure. Not wanting to sand if I...
  4. Rranger

    In the process of Sanding?

    How would it stand up on the deck with non slip grit in it?
  5. Rranger

    In the process of Sanding?

    Thanks for the heads up its right down the road at my Home Hardware. No sanding between coats?
  6. Rranger

    In the process of Sanding?

    Thanks I will check into Tremclad also.
  7. Rranger

    In the process of Sanding?

    My camo is just a choice no reason other than looks. Its just a matter of coming up with a color scheme that looks decent.
  8. Rranger

    In the process of Sanding?

    After I started sanding off the Canadian Tire crap paint that was peeling off my recently acquired Sangster boat, I read I was to degrease before sanding... I'm sanding down into a second layer that has to go then should be good to prep for primer. How big a deal was it not to degrease before...
  9. Rranger

    Spray Epoxy?.

    I don't need that thanks for the heads up. probably go carpet.
  10. Rranger

    Spray Epoxy?.

    Fiberglass in the front with peanut butter glass the bottom and joints and some sanding and ready to gelcoat.
  11. Rranger

    Spray Epoxy?.

    Like I say I'm in the process of deciding you add fuel for thought, carpet is nice no doubt about it.
  12. Rranger

    Spray Epoxy?.

    You can mix colors with the Raptor liner. Can go over top with a new layer down the road if it needs it and floor is still good. UV shouldn't be a problem if as advertised.
  13. Rranger

    Spray Epoxy?.

    One more question when I cover the new floor and old fiberglass floor any one have a reasonable priced solution. I'm looking for a roll on material I can do the floor, insides right up to the gunnel, the inside rear transom and the new splashwell. Have to be able to come up with a color I choose...
  14. Rranger

    Spray Epoxy?.

    Thanks Chris I was being lazy hoping for a quick fix.
  15. Rranger

    Spray Epoxy?.

    I plan on peanut butter and mat on corners. Going to have to suck it up and lay the mat. Been a journey getting to here..
  16. Rranger

    Spray Epoxy?.

    I changed a I/O hull to a outboard. I have my 3/8” plywood pieces for the motorwell cut and capped with 1-1/8” wooden dowel. I’m looking at matting and fibreglassing the pieces and wondering if there isn’t a easier way than cutting and applying Mat and fiberglass to encapsulate the pieces. Many...
  17. Rranger

    Using 2 different epoxy brands

    Managed to finish using the same epoxy.
  18. Rranger

    Using 2 different epoxy brands

    I am epoxying a layer of new mat on a section of floor I replaced. My question is I may run out of the epoxy I'm using and have to buy a different brand. Can I use the new brand while the first epoxy has been applied and still wet or does it need to cure first then carry on with the new epoxy?
  19. Rranger

    1993 90hp and 1994 125hp.

    The short question is will the trim tilt unit from the 1993 90hp serial 0D237792 part number 818903A1 work on the serial 0G086789 1994 125 hp part number 824051. From what I can gather the 90hp is a two wire unit same part number as units used on 1994 125 hp but a later serial number than mine...
  20. Rranger

    Cloth or not

    Poly. Used mat. One sheet on one to go. Waiting on supplies.
View older results
Top