Search results

  1. Faztbullet

    Awful Boat-Outboard Mismatch.-

    Looking at pics again...pic #5 doest look like boat as in other pics . If it is.. its had decals replaced and repositioned,pinstriped,wakeboard rack added. Engine set up on a OS bracket is different than mounting to transom.; On a offshore bracket raise 1 inch for every foot of setback. So a 2...
  2. Faztbullet

    ‘89 150 gear set replacement?

    Go here... and you HAVE to set up pinion height !! Not a drop in fix !! Good product as been using for 15 years with no problems.... https://gearprosinc.com/shop/ols/products/gp-5130-4
  3. Faztbullet

    Awful Boat-Outboard Mismatch.-

    I highly doubt that a 4 Winns hull...looks like it has been repainted and decals added and even they are in the wrong placement
  4. Faztbullet

    1986 Johnson 175 missing

    Wrong diagram as that's for looper..you have a crossflow
  5. Faztbullet

    Ignition conversion

    Nope as engine block and upper bearing housing different
  6. Faztbullet

    Low voltage on Stator blue wires for Mercury 115 HP 1991

    Check the flywheel key and RPM of flywheel determines voltage output to switchbox. Slow crank = less voltage. I suspect you have a battery/starter problem and in cold weather it is magnified. I think your old stator is fine.
  7. Faztbullet

    Low voltage on Stator blue wires for Mercury 115 HP 1991

    Either switchbox internal rectifier has a problem and dropping voltage reading or that CDI junk is bad. Test the stator disconnected from switchbox and if readings are ok when cranking replace switchbox.
  8. Faztbullet

    Mercury/Mariner Blocks Interchangeable?

    According to crank part number cranks are different,no oiling gear feature and uses bottom guided vs 150EFi which is top guided pistons.
  9. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    Lectro88...They do not make high dome pistons for OMC..that is a Merc crossflow thing. To change compression on OMC you use tighter heads. Also aluminum will not "glow". All the pistons are the same in a 150-235 crossflow..only difference is the porting, heads,CC's and carbs to get different...
  10. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    "" I am electing to avoid the crossflow/high dome pistons "" You mean high ring pistons but those hasn't been offered in many years..
  11. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    They are sometimes difficult to get thru the dealer network..Jason and I dont buy off Sleazbay
  12. Faztbullet

    Mercury Outboard 2017 150 Intermittent Missing

    Does it just miss or does it lose RPM also?
  13. Faztbullet

    hard pull

    I got its brother in shed..runs excellent but take a BIG man to rip the starter recoil. The duck hunters keep bringing it back,....I have sold/refunded it 6 times. Compression 130PSI per cylinder.
  14. Faztbullet

    Carrier bearing cracked

    Usually from being popped in gear at high idle or panic reverse. Will need all gears and bearings. Might be cheaper to find used...
  15. Faztbullet

    Help! Trying to identify my Mariner motor year!

    Tis a 1985 model...good lil motor if it has good compression. Need to find you a 3 ram trim unit ad pop it in . No more raising manually in shallow water or ramps.
  16. Faztbullet

    Carrier bearing cracked

    Internal failure of gears/dog. Taken the bolts out and yank carrier on out and have a looksee.....
  17. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    Jason was the one that did all the machine work at MarFab before they closed and if I remember correctly a BRP Master technician.
  18. Faztbullet

    Boat not as fast as expected?

    That motor was the last year before prop rating so performace is comparable to a 115HP now. Need to check that cylinder with low compression as these motors have a history of spitting rings.
  19. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    WSM supplys 80% of the aftermarket piston kits you see for sale ,other just people box them under their brand. Vertex and Wiseco are the others. The WSM's are as close to OEM but better. Call Jason and tell him Alan said call. He will give you straight up no BS answers
  20. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    Call Jason as he did the boring at MarFab. Quick turn around and I suggest WSM piston kits....and Jason can supply all. Can even short block it for ya!! One stop shopping!!! Jason White at Jay’s Block Shop in Tennessee Contact info: Jay’s Block Shop 3015 McMinnville Hwy Sparta,Tn. 38583...
Top