Search results

  1. alldodge

    Volvo Penta 5.0 gi throttle body

    I took that statement as this was during a test. That said the intake has two levels and there could be a difference but sure wouldn't think it would do that. A 0.3 difference is a bunch
  2. alldodge

    Canopy peg end

    Howdy While there may be someone which still has the part, its going to be hard to find as you have probably already determined. I would suggest changing it out for a newer style Maybe something like this, but note this is listed in the UK. Could also try another connector and rearrange...
  3. alldodge

    Bennett Trim Repair And Auto Pro Install

    pics
  4. alldodge

    2007 3350 mpi not reaching top rpm

    Howdy I would start by checking if the distributor was installed correctly If that is correct, check fuel pressure and does the throttle body fully open at WOT
  5. alldodge

    2004 Mercrusier 4.3 litre Acceleration

    This says your setup should look like this and item 15 is the filter
  6. alldodge

    Indmar 5.7 TBI transplant into 88 SeaRay - Shift Interrupt & Base Ignition Timing

    Here is the Merc ECM's
  7. alldodge

    Indmar 5.7 TBI transplant into 88 SeaRay - Shift Interrupt & Base Ignition Timing

    The NO switch is used with either. The old Dizzy used points, the new uses an electronic pickup
  8. alldodge

    Mercruiser Bravo 5.7 liter stalls when coming down to idle off of engine rev.

    Would also be a good idea to check fuel pressure. Should be 43 psi at 1800 rpm To check pressure you would need a fitting like this one to place inline at the TB part number 91-806901
  9. alldodge

    Indmar 5.7 TBI transplant into 88 SeaRay - Shift Interrupt & Base Ignition Timing

    Cool, that will make it easy to use the shift interrupter. Need the connector that plugs into the one on the right with 4 pins. Then this will be used to set timing and also for shift interrupter. You will need 12V from a key active source, (purple wire possibly). Connect the 12V to the wire...
  10. alldodge

    Bennett Trim Repair And Auto Pro Install

    The port side trim cylinder needs repaired. It is cracked on the left side top and leaking fluid. The boat is a 1994 model so its kind of old. Looks like I can get the upper actuator hinge, just looking for the best repair and not necessarily the cheapest. Most the time I don't even use the...
  11. alldodge

    Indmar 5.7 TBI transplant into 88 SeaRay - Shift Interrupt & Base Ignition Timing

    Indmar may muddy the waters, but here are the distributors EST HVS Cap Thunderbolt
  12. alldodge

    2001 SeaRay 340DA with MX6.2 Sterndrives: Starboard side no crank, electrically dead

    There should be two solenoids in the engine room, for port and starboard engines. When the switch is flipped at the helm this should energize the individual solenoids. Since you can start using the crossover, then your starboard solenoid has a bad connection or has gone out. Don't know what...
  13. alldodge

    2005 Tahoe Q4 Wiring

    If you have a single bi-color light then there will only be 2 wires and a single bulb, 12V and Ground. If your boat is larger and has two lights as shown in the port and starboard lights, then each will have a 12V and ground lead.
  14. alldodge

    really stupid question.... got my first i/o and can't figure out how to start it!

    Being a 1970, I don't think it has a man overboard kill switch. The way the throttle is located, I would think if there is anyway to get it in throttle only mode, it would need to be pushed in direction of arrow, then moved forward to throttle. With the key being unable to turn the motor over...
  15. alldodge

    2005 Tahoe Q4 Wiring

    Howdy The Nav light turns on the red/green nav lights and the white anchor light. One way it turns on both lights and the other should only turn on the anchor light. Can be wired by two methods, but one at the top is used most often Note, if your red/green lights are separated then there will...
  16. alldodge

    Engine will not start. No gauge movement!

    While this is an electrical issue, do think this should be in the Merc section Initial thought is there is a ground issue or your 20 amp fuse is blown.
  17. alldodge

    Bravo 2 outdrive removal - stuck

    The lube leak is normal for a little to leak out as the drive is removed while the male/female connector separates. It will leak more if the vales do not completely separate, the vale is held open
  18. alldodge

    87 Formula, mercruiser stalls

    Check the shift cables are adjusted correctly. The lower shift cable is seen in the vids in the adults only section. The throttle shift cable needs to have 3 inches of travel to work correctly. Here is the interrupter switch adjustment
  19. alldodge

    1984 Mercury 90 HP Tilt/Trim issues

    Howdy I think your dealing with a pump and check valve leak problem. Unable to find an outboard trim system, but have found one for a Mercruiser. The system works the same its just location and size. Note item 1 the shuttle valves. They are used to seal off the ports so fluid does not leak...
  20. alldodge

    4.3 - Alpha 1 loud clunk

    Many folks with Alpha drives put the drive in gear slowly, when it should be quick. As its starts to go in gear, you hear the gears clipping (grinding) until it is in gear. Doing this will round or chip the corners on the clutch. In the pic below it shows how to inspect
Top