Search results

  1. Scott06

    07 mercruiser 4.3 no start

    Use a VM to test Key switch could be the issue- so are you getting 12 v out of the key switch in run? If no probably the switch. if yes, then where are you loosing it from switch to coil? On a lot of boats the 12v come from key switch and daisy chains through the gauges, and probably a fuse...
  2. Scott06

    Only 3 Drain Locations?

    that may be depending on what cooling system you have I think you could have as many as 7 or as few as 1 (single point drain). issue is to make maintenance "easier" they hose over what were separate drain locations to a central or a fewer number of drain points. while in theory this is great...
  3. Scott06

    replace Mercruiser 2.5L 1989 with Mercruiser 3.0 1994

    I am assuming your old boat does not have power steering and the new engine does? the 8-10" long metal tube in the water intake hose is a powers teering cooler, this cools the PS fluid on the return line. Leave the cooler in the water inlet hose, remove the PS pump and 1/2" or so diameter hoses...
  4. Scott06

    Help me set up my new edelbrock 1409

    The over flow fuel line on the intake helps the fire start faster, so you don’t waste time just getting a whiff of smoke… the marine edlebrocks have a gold irrodite or similar finish vs the bare aluminum that the street carbs have. The bare aluminum corrodes in a car sitting in a garage … the...
  5. Scott06

    Rebuild my choke to Electric. What with the "holes"

    Yes and we know you have enough pictures already to start your quadrajet only fans site… if you know the principles of how it should work you don’t need a manual and can figure it out.
  6. Scott06

    No water coming out of the exhaust on muffs

    No what do lugs on cap look like? Mine tend to get green oxidation after a few years.
  7. Scott06

    Over heat alarm

    There are three switches on engine which can make alarm sound - high engine temp, low oil pressure, and low drive lube bottle . All three of these switches make the ground connection to the block for the buzzer. Thsee are completely separate from oil pressure and temp senders that work the...
  8. Scott06

    1990 mercruiser 4.3 no spark

    Turn distributor while cranking. If backfiring yes timing is wrong reading this wonder if you had a grounding issue on distributor to block . Not sure if third wire off sensor is a ground which would nix my theory… but if clamp is loose …
  9. Scott06

    MC1 anodes

    What prop are you running. I had zero issues with aluminum annodes in fresh when I ran aluminum props. went to a big 4 blade revolution 4 and had some pitting like u mention. This is lift kept not in a marina not connected to shore power. also found better results with oem merc magnesium vs the...
  10. Scott06

    07 mercruiser 4.3 no start

    Cycle the man overboard switch if it dies when you put key to run it’s loosing ignition this way. found that out the hard way … when starter is running ignition is powered via starter I think, when you turn key to run if man overboard is tripped there is no longer 12 v going to positive side of...
  11. Scott06

    Rebuild my choke to Electric. What with the "holes"

    that is it if you click on the pic of this intake manifold off a 165 (just swagging the engine has to be a 3.0 or 165 st 6 by pic) you will see the tube you mention https://www.marineengine.com/newparts/part_details.php?pnum=MER58759A13 if you can find a welch plug like used in carbs that...
  12. Scott06

    07 mercruiser 4.3 no start

    Does it run when holding the key to start?
  13. Scott06

    Rebuild my choke to Electric. What with the "holes"

    whats the serial number on the engine you are working on? this will help see in parts diagrams what should be there Usually the hot air style chokes had a tube inside to heat the air to the choke from the exhaust gases. On an old V8 this would be in the exhaust crossover in the intake. The...
  14. Scott06

    07 mercruiser 4.3 no start

    Loose battery cables or dead battery. Man overboard switch ? Heavy throttle - is the float bowl overflowing flooding the engine ? opening throttle wide is the way to clear a flooded engine.
  15. Scott06

    Idle setting Mercruiser 165HP

    correct. when adjusting it get the rpms right then adjust the mixture. One screw at a time, go in to lean it (slowly give engine time to react) until it stumbles, then richen it up until it stumbles. Usually in between is considered best idle. then you may have to readjust the idle speed...
  16. Scott06

    Help me set up my new edelbrock 1409

    Also was not a marine rated carb …. From a safety perspective is a big issue
  17. Scott06

    Cold Starting RPM: What is normal?

    when adjusting idle speed take the throttle cable off the carb . Adjust the idle speed. When you reattach the throttle cable adjust so it fits on where the idle screw stops the throttle. It should hold the throttle against the idle speed screw
  18. Scott06

    Cold Starting RPM: What is normal?

    Do your final adjustments on the water and in gear . I think you’ll find that 800-900 rpm is a tad high to get in and out of gear easily
  19. Scott06

    Help me set up my new edelbrock 1409

    I think from your earlier thread you have a TBV verify with first pic igntion module and probably knock module piggybacked to dist pages may be out of order but one of them has timing tune up instructions . get a factory manual as Mike said water will continue to come out (Especially if hose...
  20. Scott06

    Help me set up my new edelbrock 1409

    check or set igntion timing , tweak the idle mix screws , adjust the idle speed until maybe 675-700 out of water do final idle speed setting in water in fwd 650 or so. if it is a little lumpy the mix screws may need fattening up or leaning out
Top