Search results

  1. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    You are right. I have installed exhaust bellow without adhesive. I know there is leaking without adhesive. But it is better than the bellow comes off
  2. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    I failed again. Next time I will do it without adhesive. maybe there is a little leaking.
  3. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    In Manual # 6, I cannot find your provided guidance. Now I still have the issue for exhaust bellow installation. After I clean the outside of the mounting flange of belling house and the inside of exhaust bellow and I apply adhesive on both side, After the adhesive is not tacky any more, I...
  4. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Should I push the bellow behind the ditch. The bellow was stopped just at the position of ditch. It should be very good if I can push the bellow behind the ditch. What is the right position for the bellow of u-joint. The bellow is for QuickSilver. I have a question for applying adhesive. Should...
  5. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Yes. I did.
  6. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Has Anybody good tips to install the u-joint bellow and exhaust bellow? My The front u-joint bellow and the real exhaust bellow are loosen after I lift the outdrive too high.
  7. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Chris, I followed your viedo to adjust lower shift cable and remote control cable, then the reverse can work. Thank you so much.
  8. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Chris, Could you please list all the adjustment procedure?
  9. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Chris, This time I only change the lower shift cable . There is a viedo for engine dies. What should I adjust according to this viedo?
  10. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    How can I solve the engine stop while pull the lever to reverse? I am sure that the length of between center of hole in shift cable end guide and center of brass barrel is 6 in and Ensure shift lever adjustable stud is at bottom of slot. If necessary, loosen stud and move it to bottom of slot...
  11. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Compression is 140,140,125~130,140. Now the firing order is ok. But I do not know how to test the timing.
  12. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    During one day in the water, there some backfires from full speed to slow down. Also sometime the engine shakes when I turn engine off. sometime it does not. How can I solve the backfire issue and engine shaking? The outdrive is not the original. I will do a test to switch to my original outdrive.
  13. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    There is a little of gear biting voice while I try to shift from neutral to reverse. it seems better from neutral to forward. How can I solve this issue? I have checked that it is 6 inches.
  14. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    The bellow is tightened with the edge of the bellow house, I am concerned to rip the bellow if I force the bellow off from the edge of bellow house.
  15. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    What does you mean? I have done the fixing job, including pulling engine, replace coupler, rebuild the bellows and replace the shift cable , rebuild the base,ask mechanic to reseal the upper , finally mounting engine back and did the alignment between gimbal bearing and engine, engine and outdrive.
  16. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Achris, I did not have too much time to make the bellow to bite the edge of transom because they get stuck immediate after I applied adhesive at both side. That is why I did not put silicone last time., so it was leaking. Also it is very difficult to take bellow off if I think that the seal...
  17. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    This morning I pulled boat into water and only a little of drop water leaking while running motor. it does not leak if motor does not run. So I think it should be OK now. Yesterday I continued to do the seal job for one side of sealing for the exhaust bellow and u-joint bellow. Also I put the...
  18. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Yes. I have applied marine sealacant on it, also reseal bellows with adhesive this morning. Can I go and test in the water tomorrow after noon?
  19. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Can I apply sealecant on it?
  20. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Thank Baretta, Is it easy to install this anode? Can I find video in youtube? or can I find information in manual # 6? What is function of anode? Can I just apply sealancant on it? How long should I wait for boat water testing after bellow repairing with the applying of adhesive ? or Where...
Top