Search results

  1. L

    Mercruiser 4.3L lift points

    Today I got a new alignment bar, But I cannot push it into my gimbal bearing even the diameter is 1.3820 inches. and The old alignment bar is 1.3740. So the old one can be pushed through the gimbal bearing.
  2. L

    Mercruiser 4.3L lift points

    The alignment bar can be pushed into couupler after I filed some high spot at the end of alignment bar. Thank you Scott06 so much
  3. L

    Mercruiser 4.3L lift points

    It seems that I need not replace the coupler. The alignment bar worked before . You can see the obvious damaged edge in the second picture. I will buy another alignment bar
  4. L

    Mercruiser 4.3L lift points

    It seems that I need not replace the coupler. The alignment tools worked before . You can see the obvious damaged edge in the second picture. I will buy another alignment bar
  5. L

    Mercruiser 4.3L lift points

    It seems that the gimbal bearing installation tools touched the coupler during the installation of gimbal bearing, the alignment tools cannot be pushed into coupler and I pushed the tools very hard and the alignment tools was broken. So I doubted coupler was damaged by me while mounting the...
  6. L

    Mercruiser 4.3L lift points

    I have found another lift point at the top. is two lift point enough?
  7. L

    Mercruiser 4.3L lift points

    Can following lift straps work or not? (This synthetic nylon sling boasts a capacity of 4,800 lb basket, 2,400 lb vertical and 1,920 choker for a variety of hoisting and lifting applications. ) https://www.princessauto.com/en/1-in-x-4-ft-lifting-sling-with-end-loops/product/PA0008480170
  8. L

    Mercruiser 4.3L lift points

    I only find one handler for mercruiser 4.3L 185HP, Where are other handlers? I am going to do the coupler maintenance and need pull the engine out.
  9. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Archris, I am trying to buy genuine bellows for mercruiser alpha one and gen I. Could you please suggest which product are genuine? Could you please give me a link? Normally I prefer shopping in Amazon.ca. Thank you
  10. L

    Mercrsuiser 185HP, Unkown Serial No.

    Is the gimbal bearing good? A piece of edge of u-joint bellow house was damaged and I applied the silicon and hope it can work. Tomorrow I will install the bellows.
  11. L

    Mercrsuiser 185HP, Unkown Serial No.

    Thank you Fun times. I bought from Amazon.ca https://www.amazon.ca/dp/B09ZXMT4X3?psc=1&ref=ppx_yo2ov_dt_b_product_details
  12. L

    Mercrsuiser 185HP, Unkown Serial No.

    Gimbal bearing failed to be installed. See attached file. Can I pull it out and install again. it the new out ring is broken. Maybe I can put the old outer ring back. What reason caused the out ring failed to be pushed? or The gimbal bearing is in the bad quality?
  13. L

    Mercrsuiser 185HP, Unkown Serial No.

    Yes. I have found it.
  14. L

    Mercrsuiser 185HP, Unkown Serial No.

    I am going to install the gimbal bearing. I'd like to know how the greese is pushed into the gimbal bearing? I cannot find the any hole from the gimbal bearing house by which can be used to push grease into gimbal bearing. left gimbal bearing is old and I can see the new grease which I pushed in.
  15. L

    Mercrsuiser 185HP, Unkown Serial No.

    Can anybody help me to identify where is leaking oil from?
  16. L

    Mercrsuiser 185HP, Unkown Serial No.

    There is some leaking oil. But I do not know where it is from. Can somebody help me identify this issue? The engine oil is clean and good. I am sure the engine oil is the not same as this leaking oil. There is some oil in the second pic. Is it possible leaking from here? Also What kind of...
  17. L

    Mercrsuiser 185HP, Unkown Serial No.

    So I will follow 3'' exhaust sytem. and the water shutter part No. should be 99370A2 https://www.mercruiserparts.com/bam/subassembly/31468/919/220 Thank you
  18. L

    Mercrsuiser 185HP, Unkown Serial No.

    Attached file is my elbow, top end is 4'' and bottom end is 3'', Should I follow 3'' Exhaust System or 4'' Exhaust System? Also Can following link from Amazon is cheaper and Can it fit my engine...
  19. L

    Mercrsuiser 185HP, Unkown Serial No.

    Should I replace the water shutter assembly?
  20. L

    Mercrsuiser 185HP, Unkown Serial No.

    Should I also replace the part of water shutter assembly. I can take it off. So I am concerned that it was damaged too
Top