Search results

  1. R

    1988 Johnson 70hp inspection

    Well----Perhaps the only shop in your area.----But with the right tools about $100 / cylinder does the trick.
  2. R

    1981 Johnson 115hp 4 cyl

    If you do not know how old the impeller is you must install a new one.-----And look at the 2 thermostats and poppit valves.
  3. R

    1988 Johnson 70hp inspection

    Good used outboards with warranty are few and far between.-----Many 2 strokes are ruined by folks who do not know how they work.-----Folks invent new ways to destroy them on a regular basis.-----Learn to rebuild it properly and you will have affordable boating for a long time.
  4. R

    1988 Johnson 70hp inspection

    These are excellent motors..-----Rebuild it with 3 new pistons in there.-----But you must determine the cause of the damage.----Run it for another 20 years.
  5. R

    power trim removal of center cylinder

    I think you put a threaded rod in there.----And a slide hammer.----Perhaps your local friendly shop will pull it in minutes.
  6. R

    1981 Johnson 115hp 4 cyl

    Test the overheat horn.
  7. R

    New Stuff on Vehicles likes/dislikes

    edited
  8. R

    New Stuff on Vehicles likes/dislikes

    Factories build what people will buy.-----New car buyers are not worried about repairs on all the " high tech " stuff.----New car buyers love the gadgets and bells and wistles.------Now those on a budget just want a good engine and drivetrain along with the basics.----Some off the high tech is...
  9. R

    1980's serial number / harness / general questions

    A 2 stroke would not use an engine oil pressure gauge.
  10. R

    1971 mercury 500 thunderbolt (50 h.p.) ignition

    Belt timing checked?
  11. R

    Mid 70’s OMC. No spark.

    Post ohm reading of brown wires from stator.----Post ohm reading on one brown to ground.----Post ohm reading of sensor coil.
  12. R

    Mid 70’s OMC. No spark.

    A 1978 50 HP Johnson.
  13. R

    New Stuff on Vehicles likes/dislikes

    Not easy to find pre 1980's car in the " rust belt " areas.----just like outboards the older stuff is easier to maintain in your backyard.
  14. R

    New Stuff on Vehicles likes/dislikes

    I learned to drive long ago.---No sensors in the car because driver had the common sense back then.------I hate the " high tech " features that are big $$$ to repair.----If you hit a moose or deer it can mean a " write off " of the vehicle.
  15. R

    How should propeller “leakage / water seepage at the shaft seal” be addressed?

    Is it packing in there?----That can be adjusted to get the proper amount of leakage.----A mechanical seal should be replaced.----Pictures of your set up ?
  16. R

    1994 140hp evinrude

    Sparkplugs are not used for this test.----Buy a spark tester.----Or use some wire / glue and carboard to make one.
  17. R

    1979 Evinrude 4hp gear oil and cooling?

    It was stated that there is only 1 screw on this gearcase !!----Same gearcase as was used on earlier 2 HP motors.
  18. R

    Oil/fuel leaking from water intake Merc 40 4cyl 2S

    Pressure test the gearcase to see if there are any leaking seals.----Or just simply install a seal kit so you will not lose any sleep.
  19. R

    Need help, shift shaft height for 1996 15 hp Evinrude

    ????----Post #2 is very clear I believe.----No mention of any measurement.
  20. R

    Need help, shift shaft height for 1996 15 hp Evinrude

    The lower shift rod MUST be screwed in all the way then backed out so bend faces forward.------And the notch in the shift rods MUST be lined up with the hole in the connector BEFORE you put the screw in.----It really is as simple as that.
View older results
Top