Search results

  1. K

    Is it a Chevy or Ford engine?

    If the distributor is in the rear then it is a chevy.
  2. K

    Steering shaft removal

    That would not work. Is it possible to rotate the shaft by using a pair of channel lock pliers on the gear?
  3. K

    Popping through carb at 4000 rpm

    Is the popping sound with the same delay between events or does it do it randomly? Have you ever tried a separate small gas tank? Also with the engine off push the throttle all the way in forward then look at the roller in the ”V” notch on the shift linkage. It must be in the middle of the “V”.
  4. K

    3.7l mercruiser engine wont slow down in neutral after being revved up. Current problem is at the bottom

    It may be possible that the centrifugal advance is sticking. Remove the breaker point plate and check the springs and the posts that retain the weights. Was the carburetor a marine version that you installed?
  5. K

    Starter needed 1970 merc inline 6.

    According to the Sierra catalog the 18-5919 is for the 12 3/4” flywheel.
  6. K

    Starter needed 1970 merc inline 6.

    The best starters are the PMGR permanent magnet gear reduction. A lot lighter, take less amperage and really turn the engine. Sierra Marine # 18-5919
  7. K

    Steering shaft removal

    If you use a slide hammer be careful not to shear off the snap ring groove. First try using a crow bar to get behind the gear and also driving it in and pulling prying it out. I can feel your pain, I have had my share of those binding steering shafts.
  8. K

    Steering shaft removal

    There is a slotted head screw on the drum that the cable wraps around. if that is out then you just have to keep rotating it back and forth while pulling/prying and it will come out. There is a plastic bushing in the housing that corrosion builds up under which causes the shaft to bind.
  9. K

    Boat Names

    The previous owner of a 24’ Campbell I once owned was at a “Secret Santa” party and ended up with a pair of women’s panties. He put them on and the ladies commented, OH HE is SO SHY! Thus the boat was named. “OH SO SHY”
  10. K

    Mercruiser 140 (1984) - What started as key no longer turning off boat has evolved into boat not starting at all

    On the main starter solenoid there is a small purple/black wire next to the battery cable. Are they touching? If not try disconnecting that wire and check if the engine stops with the key off. If there is no wire like that on the starter solenoid then look at the small boost solenoid for the...
  11. K

    Help id’ing part thats smoking. 1986 aq151a

    That hose is the crankcase vent that is supposed to be plugged in to the air intake box. There should be a nipple or a hole where the hose fits.
  12. K

    Lower drive shaft seal wear.

    The worn area can be repaired with a Speedy Sleeve which can be purchased at any bearing supply or even a NAPA store. If you can measure it it should be around .875. The sleeves are stainless and do not wear out. They come with an installation kit but great care has to be used not to damage it .
  13. K

    1986 Bayliner Capri AQ131a, timing belt intermediate pulley is off position

    Sierra Marine #, 18-3889. Complete set of seals. 8 pieces.
  14. K

    Advice please

    If you find rust on the shaft next to the gear try cleaning it. Sometimes that will cause what you are describing.
  15. K

    1986 Bayliner Capri AQ131a, timing belt intermediate pulley is off position

    Most likely in the past the belt was replaced and the distributor‘s wires were moved around to compensate. Since the genuine Volvo belts are marked it is not hard to line up everything. Sometimes when the belt tensioner is released it will cause the belt to jump a tooth on one of the...
  16. K

    Another prop slipping thread

    Once the dog is locked in any gear there is no way it would slip. I am bettering on the drive coupler. Especially after the propeller has been ruled out. Full power starts pulling people really puts a lot of strain on the coupler. Upper or lower gears do not “repair themselves “ after the...
  17. K

    Ignition timing specs volvo penta aq125a

    You need to clean the carburetor. Most times the gaskets are reusable if this is a down draft carburetor. The idle metering screw is always 1.5 turns from seated. Most times 1-1.5 turns on the stop screw. Anything more than this is not right.
  18. K

    Ignition timing specs volvo penta aq125a

    If you have a new belt from Volvo it will have yellow marks that line up with the marks on the sprockets. Remove the spark plugs after the belt is installed and turn the engine by hand around enough revolutions where the marks will work themselves back to where you started. This certifies that...
  19. K

    VP 280 no reverse

    All the parts in the picture that SD posted can be replaced with the exception of #41 with out removing the drive. You need a Volvo Genuine parts and a service manual.
  20. K

    Fuel system problem on 13 yo storage boat

    There might be a fine screen filter inside the tube, be sure to remove and pitch it.
Top