Search results

  1. jerryjerry05

    1993 pontoon boat with a 40 hp Force.

    MAYBE??? It sounds like the primer/choke might be defective? Just because you hear a click doesn't mean it's working. The "click" is the primer opening and allowing a quick shot of fuel to enrich the system and making it easier to start. The primer has a diaphragm that can go bad and leak...
  2. jerryjerry05

    Force 85 HP tilt/trim model no.

    The 1989 T@T didn't come with a model or serial number it came as part of the engine package. If the "new" pump isn't working right??? Send it BACK. There's nothing you can do to it to fix it. NOTHING!! The only thing you can do to one of these pumps is to change the tiny red seals, these seals...
  3. jerryjerry05

    Force 70hp New trim motor

    IF the pump is new?? Then it's probably bad. Famous Chinese JUNK!!! What system do you have? Pictures?? They made 4-5 different systems and procedures for filling are many.
  4. jerryjerry05

    1995 Force 120 no water pumping through powerhead

    No such thing as salt deposits washing away. There are some things that will help dissolve them. Big bucket: couple gallons of vinegar and box of baking soda. Run the mix through and let it set. Run it and repeat 4-5 times. That might help, maybe not. The one sure way is take it apart and use a...
  5. jerryjerry05

    1993 Force 50hp 2cyl 2 stroke What in the Jerry Riggin'?

    Looks like someone adapted a newer Mercury ignition. outboardignition.com for testing the systems. By the way: it's Jury Rigged, Not Jerry
  6. jerryjerry05

    1995 Force 120 no water pumping through powerhead

    Pull the lower unit. The impeller shouldn't be soft and pliant. Replace it. Everyone I have seen(hundreds) is stiff and not easy to install. Old piece of hose, cut off end and run the hose up the pickup tube and run it. Running in a bucket: the bucket needs to be DEEEP at least 4" over the...
  7. jerryjerry05

    Force 5hp (1990) no telltale?

    On the mid section is a lump with 2(?) holes that the water should be coming out. Very TINY!!! wasps get into the holes and make nests. Small piece of wire up inside the hole and see if the nests/babies comes out. Reverse: it has it, just turn it around and then push the gear lever down.
  8. jerryjerry05

    Merc 40 Force - Takes forever to start

    Like Racerone suggested, check/rebuild or just clean it out. Makes a huge difference in the way it works and adds years to it's life. The brushes sluff off and they leave carbon bits in the bottom and that can short out the works.
  9. jerryjerry05

    Shifter fnr adjustment on a Force/ Mercury 125

    Once it's back together and before the oil, do a pressure test.
  10. jerryjerry05

    Adjust all 3 carbs at once or seperate ?

    You can set it anyway you like. Then do the starting fluid test: spray around the intake side and if the spray makes any difference?? Fix it as an air leak can kill your motor. THEN!! it needs to be fine tuned in the water and in gear.
  11. jerryjerry05

    Voltage regulator

    If I needed to buy a voltage reg??? outboardignition.com Force Regulator Item#194-5279 $190.
  12. jerryjerry05

    Force Vs Johnson

    The 85/90 Force were said to have the best power to weight rating for that motor. The rest is my opinion. The T@T on the Force is the weak point. But can easily be fixed with a few wrenches. They BOTH are hard on fuel. The Johnson electronics seem to last longer. Lower unit, both are about the...
  13. jerryjerry05

    what is this part and where to get one?

    IT's possible the spring inside the starter is broken or has come unwound?? Find a video and see if you can tighten the spring.
  14. jerryjerry05

    Force 125 88’ won’t run

    The first 5-6 posts cover help and tricks for fixing your motor. Look for the link and sync The way it died: it looks like the rod between the carbs might be set wrong(maybe)??
  15. jerryjerry05

    1975 chrysler 4.9 wont start

    Clean the carb? Unscrew the tiny screw on the top of the gas cap? Turn the gas on? When it's on remove the hose and see if it flows to the carb. Try removing the float bowl on the carb. Spray WD-40 or any penetrating oil on the base making sure the spray gets on the top of the bowl and the...
  16. jerryjerry05

    what is this part and where to get one?

    How about some lubrication? WD-40 can work miracles.
  17. jerryjerry05

    Force 125 88’ won’t run

    The motor can start even if the timing is off as much as 15-20d. That screw, not bad enough to make it not start. Check for TDC. Told you how on the other post.
  18. jerryjerry05

    1975 chrysler 4.9 wont start

    This or one the right size goes in the groove on the top of the crank shaft. Then the flywheel fits over the key with the slot cut in the taper. This is the part# but it might be hard finding. MAGNETO KEY F12150 You can make a key fit if all else fails. it needs to be a tight fit or it can...
  19. jerryjerry05

    Merc 40 Force - Takes forever to start

    Sounds like the primer is bad?? Cover off, key on, have someone push in the key as you touch the primer, you should feel a click. No click??? Test light, same procedure but use the test light on the wire. This should light the light. No light? Then the key switch might be faulty. Key switch: WD...
  20. jerryjerry05

    1990 spectrum blue fin 50hp force control cables

    They might work? But if they are used, I wouldn't put them on my boat. Ebay this "Morse 33 shift cable 12ft." Look through the cables they have. If the add says Morse or 33 they should be ok. Some are from China and can take up to 2 months to get.
Top