Search results

  1. jimmbo

    One cylinder, slipped prop, clutch dog

    Can the Ignition System deliver a Spark that can consistently jump a 5/16" gap? What condition are the Coils? Are the Points Clean, and set correctly, and aren't binding?
  2. jimmbo

    115 v4 2 stroke runs rough when warmed up

    2nd Step: Does the Spark consistently jump a 3/8" Gap on all Plug Wires? " they are what the turbojet manual recommended" Turbojet Manual???
  3. jimmbo

    Distributor harness 1976 mercury 115

    Where in Western Canada?
  4. jimmbo

    1994 Mercrusier 4.3l engine compatability

    Myself, I would ditch the Truck Cam, and get the Marine Grind. In my Eyes, 'Close', is good enough for Horse Shoes, Grenades, and Nuclear Weapons, but not Cam Grinds
  5. jimmbo

    Non planer

    An 85hp on a 13 1/2 ft Whaler? And somehow it won't Plane? I Smell a Troll
  6. jimmbo

    Just thought I'd share a nice photo.

    It has been at the Top of the Forum Section for about a Week
  7. jimmbo

    40hp Johnson blows 20a fuse when key is turned

    Welcome to iboats Odd that a Ignition Kill Circuit would have Voltage on it. Most I have seen work as Grounds to kill the Ignition. Of Course, I am not thinking of an ECM controlled Engine, which this motor might have that... I would be checking the Key Switch and Wires attached to it Since you...
  8. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    I would verify that the Tach is accurate-set correctly.
  9. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    That Velvety Fuzz is a Speed Killer, and needs to be removed.
  10. jimmbo

    Possible purchase of 73 Chrysler cadet

    Our 14 foot Skagit was supposedly only 325lbs for the Boat.
  11. jimmbo

    Possible purchase of 73 Chrysler cadet

    Perhaps the Decimal Point is in the wrong place....
  12. jimmbo

    Possible purchase of 73 Chrysler cadet

    From the 73 Brochure
  13. jimmbo

    Possible purchase of 73 Chrysler cadet

  14. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    Would look better in Mazda Red. Actually any Colour other than Black
  15. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    No I have no Like of the Mach Mustangs, to me they look like Fecal Matter. As for Pontiac, I have always thought they were the Ugliest of the GM Lines. I especially HATE the Grand Prix. The Only Pontiac that I liked was the 1967, and that was because of the Front End and Tail Lights of that...
  16. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    According to the Chart provided, the WOT Range for that Engine, was shown as 4800-5200
  17. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    I have found a lot of Gunk under 38, even when the rest of the Carb(s) looked Clean.
  18. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    The 67 and 68 Notchbacks were the Best Looking Mustangs, Ever. After that they actually looked Stupid. The 2005 - 2010 looked Okay, Inside as well as Outside. The Current Ones are Pathetic inside.
  19. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    Depending on what the Solvent is... Some like Lacquer Thinner, while good a dissolving Gum and Varnish, can do a Number on a lot of Plastics. Regardless of the Cleaner, the Float, depending on its Composition, shouldn't be left too Long. BRP Carb Kits will provide all the Parts that need...
  20. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    Unfortunately, the End Result is an Increase in Maniacs at the Wheel, going even Faster, cause they are Safer in a Crash, making it more difficult to Cull the Herd of bad/defective Gene Pools...
Top