Search results

  1. C

    Power trim not working just clicks.

    Sure, the PTT motor is connected to the relays or solenoids, whichever you have. relays use a 2 wire PTT motor and solenoids use a 3 wire PTT motor. Trace the wires from the PTT motor up and into the cowling. Disconnect the two (blue, green) or three (blue green, black) wires and put a...
  2. C

    Johnson 150/175 carb saw

    So it is back to cranking but not firing? If so, spray some 50::1 fuel into the carb throats and see if it will run for a second or so.
  3. C

    Why not mount transducer well below waterline?

    You could mount it next to the drain hole in the transom. There looks to be enough room to either side.
  4. C

    Random No Start with Boat

    A lot of those V6 motors have starters with solenoids that have a piston slide down a tube and physically push the starter gear into the flywheel, and at that time physically connect the electrical to the starter. The tubes can get dirty and cause the starter piston to stick. If the electrical...
  5. C

    Whoo Hoo! I have a hole in my boat...

    I recommend a structural patch on the inside and a cosmetic patch on the outside. Rough up the inside fiberglass and lay sufficient cloth over the hole to match the original thickness of the hull. No need for any putty or peanut butter, except for top layer appearance. Use the heaviest...
  6. C

    2005 200hp Mercury Optimax Water in Gas

    You are using a 6 gal tank on a 200HP engine? Thats about 20min usage tops, at high speed. You might put a proper fuel tank on your wish list. They have 12 and 24 Gal portables
  7. C

    Need control box

    I would think there are a lot of aftermarket OMC controls avail. I bought a Merc one a few years ago, w/o issue. A lot of aftermarket controls are universal and will work with Mercury, Mercruiser and Johnnyrude. You might check those out. Likely Teleflex makes one.
  8. C

    Tilt running

    Tilt switches are often the toggle kind that you use your thumb to work them. If they get water in them, the "Up" circuit can be completed with the switch in the off position. See if you can blow water out of them. If that is not it, look for rubbing wires in the control handle.
  9. C

    Why not mount transducer well below waterline?

    You want the transducer to be just under water when the boat is on plane, if you can. Depth gauges are real handy at high speed, also, however, you do not want any drag from them to rob performance. If you have a spot in the bilge with solid fiberglass, you can mount it there, flat against the...
  10. C

    Mercury 60hp Big Foot problem

    Overheat is usually a solid tone. What year motor? 2 cycle or 4 cycle? If 2 cycle, check oil level.
  11. C

    Went to the lake and nearly got that sinking feeling...

    Check the cockpit drain hoses between the ball valves and transom, for leaks. That is the place where they would leak, since it is below or at the waterline. Also check to see why the bilge pump failed to come on. You do have an automatic bilge pump, right?
  12. C

    Johnson 150/175 carb saw

    You must hold key in while cranking for choking action.
  13. C

    Temperature Gauge Not Functioning Mercruiser Alpha One, Help.

    Agreed, the connector is bad. If you can find a replacement connector, you could use some waterproof butt connectors to graft it to the old wires. something like thise...
  14. C

    Possible to get Yamaha speedometer output to show up on Garmin chartplotter?

    Gee, my chartplotter tells me the GPS speed as a normal feature, no speedometer needed.
  15. C

    Does this sound like a bad head gasket?

    Take a compression test to rule out head gasket. It sounds more like a bad ign system or flooding carb.
  16. C

    1979 mercry 140, lower unit/gearcase seal kit number

    If the bearings have any play, the seals can leak, while in use, but seal when bench tested.
  17. C

    Engine wont Start

    Mark, In my experience with that motor, the CDI unit will produce a good spark even if the voltage is down a bit when cranking. A good battery should maintain about 11.5VDC when cranking. CDI units often feed 300V into the ign coil, producing 500K volts at the plugs. If the battery voltage...
  18. C

    Evinrude 50 impeller

    It should be stiff, but turnable by hand. Make sure you use the correct key, as a lot of water pump kits have two. My J150EXECD uses the green one. The keys are wedge shaped, and impeller should be pretty loose before turning the driveshaft CW, which locks it tight. Make sure the oring under...
  19. C

    1992 XR6 150

    The OEM of the cables usually has a guide to measurement of the cables on their web site. I would use that vs other non-oem sources.
  20. C

    Evinrude 50 impeller

    Gee, I gave you the substitutions. I even advised on where they should be used. They are readily available and reasonable in price.
Top