Search results

  1. Scott06

    I need help, boat runs rough and stalls. I pumped new gas and lots more.. I need help

    Look on summit racing for the module I think their ac delco modules were under $100. if those primary side coil ohms are accurate yes get new coil.
  2. Scott06

    Shift shaft seal on alpha gen two

    I saw the entire cover or bushing too. Did the grease and sealer. Will do it again , get bushing if it doesn’t hold. Hopefully I find a nicked lip when I dissemble it
  3. Scott06

    3.0 tap/knock

    I would be checking the clearances and also wrist pin. doesnt sound like valvetrain to me but could be. Even if it was machined check them always. I have had to take rods back that were resized wrong. was it bored? I had an old volvo that on real cold starts would have some piston slap until...
  4. Scott06

    Shift shaft seal on alpha gen two

    Just got done doing a reseal and a few bearings in my 2004 gen two. Pressure tested it , passed , filled it with lube and laid it on the garage floor for a month, was gonna put it back on the boat this weekend, found lube leaking out of shift shaft seal… which I just replaced. I bought two...
  5. Scott06

    I need help, boat runs rough and stalls. I pumped new gas and lots more.. I need help

    Sometimes people have trouble getting them into base, which is why I suggested just setting the total advance. If total is ok let the base fall where it may. you mention replacing parts because they are 27 years old. No sense replacing oem quality parts with a $13 part of Amazon. There is too...
  6. Scott06

    Prop Recommendation: '85 Merc 50hp 2-stroke - 16' Alumacraft

    Did you check out the ignition system too? this sounds similar to my neighbors issue a few years back, wouldn't get full revs under load, but ran basically ok otherwise. He had a cylinder that wasn't getting spark did have enough azz to get going with a dead cylinder.
  7. Scott06

    Prop Recommendation: '85 Merc 50hp 2-stroke - 16' Alumacraft

    A prop missing part of a blade would allow it to over rev rpm not be 2-3 k lower than recommended WOT RPM. I would go through the fuel system and rebuild carbs first, verify your ignition is up to snuff and good spark on all cylinders, then start playing with props. You can not asses what prop...
  8. Scott06

    Replacing an Alpha1 Gen1 205 V6 for 87 Cobalt 17BR

    Additionally the ratio should be stamped on port side below the vent plug on upper.
  9. Scott06

    Replacing an Alpha1 Gen1 205 V6 for 87 Cobalt 17BR

    Yes a 4.3 V6 engine will use a 1.81 ratio drive. Yours is an alpha gen 1 so an SEI drive in that ratio is the easiest bolt in replacement . usually when the upper gear shred it is low on lube. I would frequently check the lube level. likely the input shaft seal leaked oil into the bellows and...
  10. Scott06

    4.3lx power steering fluid cooler replacement

    My money is on this. tighten the clamps see if they are loose
  11. Scott06

    Stern Drive Mystery

    As mentioned by others reving in neutral doesn't mean anything. This is why they always recommend doing a water test under load. Of course as the seller I wouldn't insist on it ... last time I sold a boat he didnt even ask me to start it. How long did it sit? Could be contaminated fuel gummed...
  12. Scott06

    Torn seal leaking gear lube

    Yes there is a small quad ring (basically a square O ring) that can get knocked out or forgotten when you reassemble the two halves of the drive. Lube leaking out the water intake is most likely the seal below the impeller. He may have taken the bearing carrier off to replace the seal then not...
  13. Scott06

    Starved for fuel

    Depending on year, MerCruisers had mechanical or electric fuel pumps. What do you have? a 3.0 carbed motor will have a mechanical fuel pump. Lets back up - 3 yrs ago carb rebuild running well? Did a tune up ? What was done during tune up? Timing set correctly - some require being in base...
  14. Scott06

    Starved for fuel

    What are u working on. What did the contents of tank you emptied look like? If it was running fine what prompted you to empty the tank
  15. Scott06

    Torn seal leaking gear lube

    Keep going to second mechanic. First guy probably tore the driveshaft seals in upper when he reassembled after splitting the unit to do the water pump... then didn't tighten the u joint nut when he replaced these seals. So yes first guy didn't assemble it correctly. I would dispute the...
  16. Scott06

    I need help, boat runs rough and stalls. I pumped new gas and lots more.. I need help

    for me was the '94 VW Fox. I bought my advance timing light in the early 90's. The Sun Pro Tach and Dwell I bought at the same time just died, so I took the one out of my dads garage "All American" brand ... I think is from mid 60's - still works... if you dont drop it it will be a lifetime...
  17. Scott06

    I need help, boat runs rough and stalls. I pumped new gas and lots more.. I need help

    Your mark is on the pulley not balancer? You can do the math to figure out where 27 degrees BTDC is and put a chalk, paint white out...what ever mark . Some auto parts stores have loaner tools like timing lights. If you have a gear head in the neighborhood or older guy who is shade tree...
  18. Scott06

    Mercruiser 250hp Stern Drive Bravo 3 leg dirty sea Strainer

    As above sea water strainer will be between the raw water pump and the drive or through hull pick up. Once you open it water can come in so make sure it is valved off ... top of strainer should come off
  19. Scott06

    Mercruiser 250hp Stern Drive Bravo 3 leg dirty sea Strainer

    Id start by getting the weed growth off the outdrives or do u have through hull water pick ups? If you have a strainer and yiu can close them off in the water open them and see what’s in there. Also could be an issue with the raw water pump impellers. If flow is restricted they may have been...
  20. Scott06

    I need help, boat runs rough and stalls. I pumped new gas and lots more.. I need help

    In theory yes unless you are look8ng for an issue. Never hurts to confirm if total advance is correct. If the module is not working right and yiu don’t get enough advance you will be down on power. Alternatively too much advance can cause detonation and the engine will hammer itself to death
Top